0
Enter the follow bonds in order of increasing bond stretching frequency C-H F-H O-H N-H?
Wiki User
∙ 12y ago
C-h < n-h < o-h < f-h
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Name two gases that can enter leaves through the pore?
Carbon Dioxide (CO2) and Oxygen (O2) can enter leaves through the pore.
Where in the body does oxygen enter the body?
Lungs
Do glucose and water enter the filtrate?
no glucose does not
How does chlorine enter the oceans?
density currents.
How do materials enter and leave the nucleus?
Materials enter and leave the nucleus through the selective membrane. The membrane always controls what leaves and enters the nucleus.
How do you program a BC370CRS scanner?
http://www.uniden.com/pdf/BC92XLTom.pdfThe manual knows all.Straight From the Manuel:Storing Known FrequenciesInto Channels1. Press Hold. Then enter the channel number where you want to store a frequency, then press Func and Pgm. The channel number appears.2. Use the number keys and to enter the frequency (including the decimal point) you want to store.3. Press E to store the frequency into the channel. Notes:• If you entered an invalid frequency in Step 2, Error appears and the scanner beeps three times. Enter a valid frequency.• The scanner automatically rounds the entered number to the nearest valid frequency. For example, if you enter 151.473 (MHz), your scanner accepts it as 151.475.• When you enter a frequency into a channel, the scanner automatically turns on the delay function and DLY appears. When delay is turned on, the scanner automatically pauses scanning2 seconds after the end of a transmission before scanning proceeds to the next channel. To turn the function off or on, press Func + Dly.• If you enter a frequency that has already been entered elsewhere, the scanner sounds an error tone and displays the channel that was duplicated. If you entered the frequency by mis- take, press then enter the correct frequency. To enter the frequency anyway, press E to accept.4. To program the next channel in sequence, press E then repeat Steps 2 and 3.
How do you enter the code in icy tower?
u can enter it by follow the intrctions
What is the fate of the energy in the ultraviolet light incident on glass?
Ultraviolet is too high frequency to enter glass and infrared is too low.
How do you program a regency scanner z45?
01) Press Manual to enter the manual mode. 02) Enter frequency. 03) Enter channel number (e.g. for channel 1, enter 01). 04) Press Manual again. Note: When entering a number of channels, you can start at step 2 after the first frequency is entered.
Why frequency of light is not change When it enter from a rarer medium to denser medium?
Frequency is a function of the energy level of the photon. Changing the medium does not change that energy level.
What happened as Waves from deeper waters enter shallower waters?
Amplitude and frequency increase and speed decreases
How do you say whatever in Gaelic?
enter a building - Téigh isteach enter your details - Cuir/Líon isteach
Where do you enter the contest to get a free membership card for pixie hollow?
its in the pixie centerl section and then you click contests and follow the instructions to enter
How do you enter the access code on spy island?
The codes are shown by the satellite clue overlays. Enter each of the three codes separately : Laser (enter) Hair (enter) Removal (enter). Follow Director D through the open transporter.
Why does wavelength o light decrease when enter to denser medium?
That is because the light's SPEED decreases. Also, because the frequency doesn't change. As a reminder, the wavelength is equal to the speed of the wave, divided by the frequency.
In Sims 3 can you follow sims to work?
yes, you can follow them to the location, but you cant actually enter it. so you can't watch your sims work
Experience as a result of the depletion of the ozone layer?
Ozone depletion causes UV to enter. these are high frequency rays of the sun.
