0
A cyclic, regenerable process for cracking of petroleum distillates to produce high-octane gasoline from higher-boiling petroleum fractions; synthetic or natural bead catalysts of activated hydrosilicate of alumina may be used. Also known as Houdry process.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Main ingredients of polystyrene?
It starts with steam cracking of oil or reforming of natural gas to get a compound called Ethylene (C2H4) which is the first precursor chemical neeeded. Benzene is also used and is extracted from crude oil by catalytic action on a particular fraction of the oil stream. Benzene and Ethylene are combined to make Ethylbenzene Ethylbenzene is mixed with hot steam on a catalytic bed to make Styrene Then an initiator like benzoyl peroxide (very similar chemical to the catalyst that you mix to make Bondo putty with) is mixed with the Styrene which starts a reaction which is called a free radical polymerization which basically puts all those light gas bubbles in the liquid styrene and also causes it to turn to a solid
Is there water around a water bed?
No... there's only water IN a water bed. Unless your bed breaks of course...
Is the sleep number bed toxic?
is the cover of the sleep number bed toxic
How do you get black ink out of bed sheets?
To remove black ink from the bed sheets. You require an amount of petrol for wash your bed sheet. Then pour it in detergent hot water and wash it softly. It may possible black ink disappear from the bed sheets.
What is composition of bedmaterial?
pillow,bed sheets,bed covers,comforters,cots,beds,crib,bassinets etc are bed materials.These are used during sleeping time.Sometimes ,these used as resting commodities.
What has the author Sunday Eghwomoni Isiakpere written?
Sunday Eghwomoni Isiakpere has written: 'The dynamics of a fixed bed catalytic reactor with complex kinetics'
What is a fixed bed?
operation at which the operation remains constant with time.
How was the problem on making the foldable bed fixed?
The problem is that if it was fixed it will take more space than folding.Gurjot Singh Sodhi
What is dual bed catalytic converter?
2 compartment for reaction, one for oxidizing of HC and CO, and other for NOx reduction.
Does a 1984 ford f 150 have a catalytic converter?
It has two cats. Both under the cab and the muffler is under the bed of the truck.
What is the difference between milling and planner?
The main defference is in Milling Machine job is fixed and tool will move. For planning machine tool is fixed and bed will reciprocate.
Why would your cat purposely pee on your bed. The litterbox is cleaned daily and she's fixed. Got her two months ago and this is a first. Walked over and peed a lot on my bed and walked away?
It's probably just a scent thing.Even fixed cats do stuff like that sometimes.
How do you fix the bed on a pop up camper?
The bed on a pop up camper can be fixed several ways but it depends on what is wrong with it. If it is just a matter of what sheets to use, the typical size is Queen and it is made by covering the cushion with the sheets. If the bed is in need of reinforcement a new bed tray can be made with plywood.
What is a gap bed lathe?
The bed of a lathe is the central beam that runs down the machine. The head, which holds and turns the workpiece, is fixed at one end, there is a tailstock at the other end which can be adjusted along the bed, and usually a carraige in between, which holds turning tools. The workpiece that can be turned in the lathe is limited to what will fit in the head without hitting the bed. A gap bed lathe has a gap in the bed near the head, so a larger workpiece can be turned.
How do you say sofa bed in French?
A sofa bed is "un canapé-lit" or "un clic-clac" depending of the system (the canapé-lit has a fixed back, while the back is used to sleep on with a clic-clac)
Should i sleep outside or in a bed full of bugs?
Sleep outside until the bed bug problem is fixed
What is a lathe bed?
The bed of a lathe is the central beam that runs down the machine. The head, which holds and turns the workpiece, is fixed at one end, there is a tailstock at the other end which can be adjusted along the bed, and usually a carraige in between, which holds turning tools. The workpiece that can be turned in the lathe is limited to what will fit in the head without hitting the bed. A gap bed lathe has a gap in the bed near the head, so a larger workpiece can be turned.
