0
As a PE home inspector, there are some locations where this can be very desirable to balance heat in an older house. However I cant seem to find any product that you can add to the pipes, like a clip on
There is now a clamp on set of fins called Fin Clamp Element.
Just type fin clamp element on any major search .
What else can I help you with?
What do you add or subtracting to change a state of matter?
To change the state of matter, you need to add or remove energy. For example, to change a solid to a liquid, heat is added to increase the temperature until it reaches the melting point. Likewise, to change a liquid to a gas, heat is added to increase the temperature until it reaches the boiling point.
Can you add a little bleach to the water to keep my hydrocollator heat pack clean?
It is not recommended to add bleach to the water in your hydrocollator heat pack as it can damage the materials and affect its performance. Regular cleaning with mild soap and water, followed by thorough rinsing, is a safer and more effective way to keep your heat pack clean.
How do people change the state of matter?
If the matter is in a liquid state, add heat to turn liquid to vapor. Remove heat to form a solid. If it is in the form of a vapor, remove heat to form a liquid, and remove more heat to form a solid. If it is in the form of a solid, add heat to turn it into a liquid. Add more heat to turn into a vapor.
How do you remove corrosion from copper pipe?
First the pipe and cap must be dry. There can be no water the pipe that will be close enough to the joint to feel the heat. You will need Soldering Flux, Solder, Emory Paper and a hot Torch. Turbo Torch is a good one, if you use MAPP Gas. Sand the pipe with the Emory Cloth until it is clean and shiny all the way around. (The width of the cloth is fine.) Sand the Cap the same way. Put Flux on the copper pipe and inside the cap. Put the Cap on the pipe, push it all the way down. Take the torch and heat the cap on it's side in one spot while holding the Solder on the opposite side at the point where the bottom of the cap and the pipe meet. When the joint is hot enough the solder will melt and start to draw into the joint. After a few more seconds remove the heat and melt solder all the way around the joint in one quick motion. You can wipe the joint with a rag if you like to make it look better before the solder hardens. Don't use Nylon or any other cloth that might melt.
What happens to acetone molecules when you add heat to a breaker of liquid acetone?
When heat is added to a beaker of liquid acetone, the acetone molecules gain energy and begin to evaporate into the air as a gas. The increased temperature causes the molecules to move faster and escape the liquid phase.
How do you add water to baseboard?
You would add it to the boiler
What would be the best way to add a heat exchanger to a 13hp engine?
That would depend on what you are trying to accomplish.Add engine cooling to an air cooled engine? Try an oil cooler.Trying to capture heat to heat something like a room? A exhaust to air heat exchanger. Basically a pipe run through the room you are trying to heat.Trying to warm water off a air cooled engine. Its pretty easy, you need a coil of copper tubing, or steel. Where the exhaust comes out of the engine you coil you tubing around a pipe from there, at the end of the pipe you cap the pipe but leave a gap so the gasses can escape and slide a pipe over the whole thing so the gasses go to the end of the pipe then turn around and flow over your coiled heat exchanger. The you run water through it at the rate that gives the temperature water you want.
Do you need to add or subtract heat make a solid into gas?
Add heat.
How do you add a second toilet to an existing drain?
All you have to do is add a "Y" pipe or Call a plumber
How do you draw a fish?
Draw an oval that is longer than it is wide, then add triangle for fins and tail then close to where you draw the eyes and mouth, but not to close draw three curved lines for the gills
How do you add a water line off of an existing pipe?
By installing a "TEE"
How do you install motorcycle baffles?
Remove the heat shield (if there is one) locate the set screw hole, remove the old baffle (if there is one) insert the new baffle with the screw hole mating up with the pipe hole, add a lil' blue locktite to screw, and screw it into the baffle through the pipe. Re-attach heat shield (if there was one removed). If baffle is a quite one with fiberglass wrapping...leave it on.
How do you install baffle?
Remove the heat shield (if there is one) locate the set screw hole, remove the old baffle (if there is one) insert the new baffle with the screw hole mating up with the pipe hole, add a lil' blue locktite to screw, and screw it into the baffle through the pipe. Re-attach heat shield (if there was one removed). If baffle is a quite one with fiberglass wrapping...leave it on.
How do you heat water without energy?
No energy, no heat. So you cannot add heat.
What are the differences between wainscoting and baseboard, and how can they be effectively combined to enhance the overall aesthetic of a room?
Wainscoting is a decorative paneling that covers the lower portion of a wall, while baseboard is a trim that covers the joint between the wall and the floor. Both can be combined to create a cohesive and visually appealing look in a room. To enhance the overall aesthetic, consider using complementary colors and styles for wainscoting and baseboard, ensuring they work together harmoniously to add depth and character to the space.
Matter changes if you add what?
heat
How do you determine invert from one manhole to another?
Given one invert, and the length of the pipe and the slope of the pipe, you multiply the the length of the pipe by it's slope (expressed as a decimal ratio) and add the result to the known invert.
