answersLogoWhite

0

By installing a "TEE"

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Engineering

Will a quarter inch pipe stepped up to half inch pipe result in a lower pressure for an outside hose bib or do I need to keep all at a half inch to add the hose bib?

i believe the pressure does not change but the volume of water you will be able to use will be less


How far should the drain pipe come out of the wall for a bathroom vanity?

The pipe out of the wall usually only sticks out a couple of inches. You add what is needed to the sink drain.


Do you need a second main drain line if you add a second and third bathroom to both ends of the third floor of a home?

a home typically has a 4" main drain and that is enough. if it is not 4" you should get a plumbing code and do the math. Can you add a second 3-inch wasteline to an existing 3-inch main house wasteline in order to add the 3rd bath and toilet (this is obviously a 1950's house)?


How do you add water to baseboard?

You would add it to the boiler


How can select weldolet or pipe to pipe for branch connection?

Do not know the term, Weldolet, but if your question is where or how do you decide where you are going to cut a pipe to add a branch line, then it is a matter of where it is possibe and the easiest to do. It is not always as close to where you would like it, but where it makes the most sense to do it. Depends on the type of pipe involved also. Copper or PVC you can cut any place you want. Steel, you can replace a coupling with a T and a union if it is in the middle of a run. With steel either black or galvanized you will have to add a union or go back to the end of the run and take everything apart. Weld-o-lets are sized for the diameter of the pipe you are tying into and the diameter of the pipe you are adding. Example: 2" x 3" or 6" x 10". If you need the branch pipe to have a theaded connection you would select a Thread-o-let instead. Sizing is the same. Some o-let's can be used for a range of piping sizes. Example: a 3/4" thread-o-let may have 8-12 marked on it meaning you can weld it on to either 8", 10" or 12" pipe.

Related Questions

How do you add a second toilet to an existing drain?

All you have to do is add a "Y" pipe or Call a plumber


How can I add a valve to my existing plumbing system?

To add a valve to your existing plumbing system, you will need to locate the section of pipe where you want to install the valve. Shut off the water supply to that area, cut the pipe, and install the valve using the appropriate tools and materials. Make sure to follow all safety precautions and local plumbing codes. If you are unsure, it is recommended to consult a professional plumber for assistance.


How to add a nipple to airconditioner for recharging?

A saddle valve is available that clamps on an existing line.


How can I extend the AC drain pipe to prevent water leakage and improve drainage efficiency?

To extend the AC drain pipe and prevent water leakage while improving drainage efficiency, you can add a PVC extension to the existing pipe. Ensure the extension slopes downward to allow proper drainage. Additionally, consider installing a trap or a vent to prevent clogs and improve airflow. Regularly inspect and clean the drain pipe to maintain optimal performance.


What is product line filling?

To add new products to a product line, e.g. if you have a shampoo, you'll add more different shampoos to the product line to increase the market share. This might include that your new product has minor enhancements compared to the existing products (including the products of you competitors). To add new products to a product line, e.g. if you have a shampoo, you'll add more different shampoos to the product line to increase the market share. This might include that your new product has minor enhancements compared to the existing products (including the products of you competitors). "Line filling is the type of product line extension to introduce new version of existing product in the market."


Can a second hot water heater be added to existing water system to add hot water supply to the house?

Yes


How do you add caller id to existing land line phone?

Call your phone company or go to their site and sign up.


How can you connect two washing machines to a single standpipe?

There are a couple of different ways to connect two washers to a single standpipe. You could add two (or one other) spigot to the stand by cutting and splicing the spigot into the pipe. The easier way might be to just add a faucet splitter to the existing spigot. The problem may lie in water pressure, however, if the pipe is not properly pressurized. If you are in a rental space, make sure connecting to the pipe is allowed, as they are often reserved for fire fighting purposes.


How can I add an electrical outlet to an existing line?

To add an electrical outlet to an existing line, you will need to turn off the power to the circuit, locate the nearest junction box, and connect a new cable from the junction box to the new outlet location. Make sure to follow all safety precautions and consult a professional if needed.


How can I add a water line to my fridge?

To add a water line to your fridge, you will need to first locate a nearby water source, such as a kitchen sink or a water line in your home. Then, you will need to install a water line kit that connects to the fridge's water inlet valve. Make sure to follow the manufacturer's instructions carefully and consider hiring a professional plumber if needed.


How do you add extra venting to existing plumbing?

Cut into the existing drain where you feel it would help the most and run a vet to the outside, preferably to above the roof line. At the point furthest from the main drain.


Can you add a freon charging valve on refrigerators?

Yes. The easiest is a clamp on style that bolts straight to your low pressure pipe/tube and pierces the line.