0
What else can I help you with?
What element is a main component of borax?
Boron is the main component of borax, which is a naturally occurring mineral compound. It is commonly used in household cleaning products and as a multi-purpose cleaner.
Why does the water move around in one toilet when the other toilet is flushed?
There are two main reasons... 1. If the toilets are mounted back-to-back on opposite sides of a wall, some of the movement can be attributed to mechanical transmission of vibration from one to the other due to a structural connection. 2. Suction in the drain. Toilet drains have vents that allow air to move in and gas to move out. If the vents are improperly installed or get clogged they can create a suction in the drain pipe that jiggles the water in other toilet bowls. 3. The theory that this movement is caused by Toilet Gnomes becoming jealous of the attention that other Toilet Gnomes are getting and then scrambling around in a panic is false.
What are the three components of human solid waste?
The three components of human solid waste are feces, urine, and toilet paper. Feces are the solid waste material that is expelled from the body through the rectum, while urine is the liquid waste excreted by the kidneys. Toilet paper is the material used for hygiene purposes after using the toilet.
What is in dry erase board cleaner?
Dry erase boards are boards that have replaced most chalkboards in the classroom. The main ingredients in the cleaners to clean these boards are alcohol, 2-butoxy ethanol and dichloroacetic acid.
What are the main ingredients in Windex?
The main ingredients in Windex glass cleaner are water, 2-hexoxyethanol, isopropanolamine, sodium dodecylbenzene sulfonate, and lauramine oxide. These ingredients help to dissolve grease, grime, and dirt from glass surfaces.
What are the ingredients of the works toilet bowl cleaner?
The main ingredient in The Works toilet cleaner is hydrogen chloride. That is hydrochloric acid when mixed with water.
What is the purpose of an overflow pipe in a toilet?
The purpose of an overflow pipe in a toilet is to prevent the toilet bowl from overflowing by providing a secondary pathway for excess water to drain out if the main drain gets blocked.
Why when you flush a toilet on the main floor an air pocket comes into the bowl in the basement toilet?
This could be an indication of a blockage or you may need to install more venting lines.
When you flush your toilet the water rises in the bowl and the stuff doesn't flush away What is wrong?
The main drain is plugged. You may need to remove the toilet and snake directly down the drain.
Can you provide a detailed toilet drain diagram for better understanding of the plumbing system?
A detailed toilet drain diagram shows how waste from the toilet flows through the plumbing system. It typically includes the toilet bowl, trap, waste pipe, vent pipe, and main sewer line. The waste is flushed down the toilet bowl, goes through the trap to prevent sewer gases from entering the home, then flows through the waste pipe to the main sewer line. The vent pipe allows air to enter the system, preventing suction and ensuring proper drainage. This diagram helps understand how the plumbing system works to remove waste from the toilet effectively.
Do you need a trap for a basement toilet?
A trap doesn't cause the blockage. Something IN sewer line causes a blockage.
What are the different types of toilet holes and how do they affect the flushing mechanism of a toilet?
There are two main types of toilet holes: rim holes and siphon jet holes. Rim holes are located around the top rim of the toilet bowl and help to create a swirling action when flushing. Siphon jet holes are located near the bottom of the bowl and help to create a strong suction force to remove waste. The size and placement of these holes can affect the flushing mechanism by influencing the flow of water and the efficiency of waste removal.
What are the different types of toilet valves available in the market?
There are three main types of toilet valves available in the market: fill valves, flush valves, and flapper valves. Fill valves regulate the water level in the tank, flush valves release water to flush the toilet, and flapper valves control the flow of water from the tank to the bowl.
What kind of plumbing problem causes a wet floor when toilet is flushed and water is backed up in the shower next to it. The toilet bowl has not refilled but the toilet water reservoir is full.?
Sound like you have a clogged toilet and or a clog in your main drain under your toilet. Shut off water supply to toilet remove water from toilet tank. Puchase a wax ring for your toilet prior to disconnecting toilet from supply line and floor bolt on the right and left of your toilet. Remove toilet from floor if water is standing in pipe under where toilet was this is where your problem lies. If no water or clog present, turn toilet on side and lokk in hole at the bottomof toilet. Clear was is stuck in toilet clean off old wax ring install new one and put toilet back together.
Why is it necessary to be able to thicken a sauce with a roux without making lumps if the sauce is going to be strained anyway?
The lumps would just be wasted thickener, and lumps are not to happen in the first place. What you do is in a separate bowl, pour some of the sauce in that bowl and mix with all ingredients you use in a roux. When that mixture is completely mixed, you then add it to the main sauce mixture and there will be no lumps if you stir it enough.
Can snails live in a toilet?
Only if you feed them and have water circulation. If you flush the toilet often or use it for it's main purpose, the snails will probably be flushed away or poisoned. If you clean the toilet bowl and they are living there they will be killed. They can, however, probably live in the tank of the toilet, considering that the water circulates. With no source of food, though, they will die. ~Wigglerthefish Fish Help Forum
Why would a toilet that has been working properly just stop flushing even though the tank and the bowl both fill up?
there can be many reasons and I will say my thoughts on just a few. 1. your toilet trap of the bowl is clogged with debris (toys, balls, etc) to fix = snake out toilet bowl or if necessary pull toilet bowl and snake backwards threw trap. 2. your tank flush flapper is closing to soon or your tank water level is not at right height to fix = change flapper or adjust water level height 3. your toilet arm before the vent is plugged because of back grade or debris clinging to the side of the drain pipe to test = pull toilet and run toilet water supply full on down threw toilet flange and see if any back flow. 4. your toilet main line is clogged from backgrade,roots,damaged pipe,etc but will let other fixtures slowly drain to test = camera toilet line from toilet flange out to street or septic or if no camera available then fill tub full and lav full and drain both at the same time and look at your lowest fixture trap to see if any back flow exists or open clean outs and if possible to see water flow .
