carbon
disulphide
Gunpowder is a mixture of nitre (potassium nitrate) , sulphur and charcoalName of the method- filteration , evaporation and solvent extraction.Steps-1) Put the constituents in water. nitre will dissolve in water.2) Filter the soln.Filterate- water+nitreResidue - sulphur+charcoal3) Perform evaporation on the filterate.Water will evaporate leaving nitre.Solvent extraction-4) Put the residue in carbon disulphide.Sulphur will dissolve in this soln.5) Filter the soln.Filterate-carbon disulphide+sulphurResidue- charcoal6) Perform evaporation on the filterate.carbon disulphide evaporates leaving sulphur.in the form of a paragraph:-Answer: Gunpowder is a mixture of sulphur, charcoal and potassium nitrate (nitre). When water is added to the mixture potassium nitrate dissolves. The mixture is then filtered. The filtrate is potassium nitrate solution while the residue is a mixture of sulphur and charcoal. The filtrate is evaporated on a sand bath to obtain nitre back. When carbon disulphide is added to the residue, sulphur dissolves. When this mixture is filtered the filtrate is sulphur solution while the residue is charcoal. Leaving it open evaporates the sulphur solution. Carbon disulphide evaporates and sulphur crystals are left behind.
Gunpowder is a mixture of nitre (potassium nitrate) , sulphur and charcoal Name of the method- filteration , evaporation and solvent extraction. Steps- 1) Put the constituents in water. nitre will dissolve in water. 2) Filter the soln. Filterate- water+nitre Residue - sulphur+charcoal 3) Perform evaporation on the filterate. Water will evaporate leaving nitre. Solvent extraction- 4) Put the residue in carbon disulphide. Sulphur will dissolve in this soln. 5) Filter the soln. Filterate-carbon disulphide+sulphur Residue- charcoal 6) Perform evaporation on the filterate. carbon disulphide evaporates leaving sulphur.
SOLUBILITY OF SULPHUR IN CARBON DISULPHIDE:Because carbon disulphide and sulphur both are non polar molecules therefore, sulphur is soluble in carbon disulphide while water is a polar molecule and not allow sulphur to dissolve
One method of separating sulphur from a mixture of carbon particles and rolled sulphur is by using a process called sublimation. Since sulphur sublimes at a lower temperature compared to carbon, you can heat the mixture to a specific temperature where sulphur will vaporize and then condense back into solid form separately from the carbon particles. This way, you can isolate sulphur from the mixture.
You can use a magnet to separate the iron fillings from the sulfur powder. The iron fillings will be attracted to the magnet, allowing you to easily separate them from the sulfur powder.
Gunpowder is a mixture of nitre (potassium nitrate) , sulphur and charcoalName of the method- filteration , evaporation and solvent extraction.Steps-1) Put the constituents in water. nitre will dissolve in water.2) Filter the soln.Filterate- water+nitreResidue - sulphur+charcoal3) Perform evaporation on the filterate.Water will evaporate leaving nitre.Solvent extraction-4) Put the residue in carbon disulphide.Sulphur will dissolve in this soln.5) Filter the soln.Filterate-carbon disulphide+sulphurResidue- charcoal6) Perform evaporation on the filterate.carbon disulphide evaporates leaving sulphur.in the form of a paragraph:-Answer: Gunpowder is a mixture of sulphur, charcoal and potassium nitrate (nitre). When water is added to the mixture potassium nitrate dissolves. The mixture is then filtered. The filtrate is potassium nitrate solution while the residue is a mixture of sulphur and charcoal. The filtrate is evaporated on a sand bath to obtain nitre back. When carbon disulphide is added to the residue, sulphur dissolves. When this mixture is filtered the filtrate is sulphur solution while the residue is charcoal. Leaving it open evaporates the sulphur solution. Carbon disulphide evaporates and sulphur crystals are left behind.
When a mixture of iron filings and sulfur is put in carbon disulphide in a test tube, the sulfur will dissolve in the carbon disulphide, leaving behind the iron filings. The iron filings can be separated from the solution using a magnet.
Gunpowder is a mixture of nitre (potassium nitrate) , sulphur and charcoal Name of the method- filteration , evaporation and solvent extraction. Steps- 1) Put the constituents in water. nitre will dissolve in water. 2) Filter the soln. Filterate- water+nitre Residue - sulphur+charcoal 3) Perform evaporation on the filterate. Water will evaporate leaving nitre. Solvent extraction- 4) Put the residue in carbon disulphide. Sulphur will dissolve in this soln. 5) Filter the soln. Filterate-carbon disulphide+sulphur Residue- charcoal 6) Perform evaporation on the filterate. carbon disulphide evaporates leaving sulphur.
it is a compound
Gunpowder is a mixture of nitre (potassium nitrate) , sulphur and charcoal Name of the method- filteration , evaporation and solvent extraction. Steps- 1) Put the constituents in water. nitre will dissolve in water. 2) Filter the soln. Filterate- water+nitre Residue - sulphur+charcoal 3) Perform evaporation on the filterate. Water will evaporate leaving nitre. Solvent extraction- 4) Put the residue in carbon disulphide. Sulphur will dissolve in this soln. 5) Filter the soln. Filterate-carbon disulphide+sulphur Residue- charcoal 6) Perform evaporation on the filterate. carbon disulphide evaporates leaving sulphur.
You should ask someone
SOLUBILITY OF SULPHUR IN CARBON DISULPHIDE:Because carbon disulphide and sulphur both are non polar molecules therefore, sulphur is soluble in carbon disulphide while water is a polar molecule and not allow sulphur to dissolve
To separate copper strips from sulfur powder, you can use a process called filtration. Mix the copper strips and sulfur powder with water to form a mixture. Then, pass the mixture through a filter paper to separate the solid copper strips from the sulfur powder, which will remain in the filter paper.
One method of separating sulphur from a mixture of carbon particles and rolled sulphur is by using a process called sublimation. Since sulphur sublimes at a lower temperature compared to carbon, you can heat the mixture to a specific temperature where sulphur will vaporize and then condense back into solid form separately from the carbon particles. This way, you can isolate sulphur from the mixture.
put this mixture in water. salt will dissolve in water. now filter this solution with a filter paper. we will get particles of charcoal on the filter paper as residue. now heat the solution of salt and water .the water will evaporate leaving behind salt. thus the mixture of charcoal and salt is separated.
Carbon disulfide is a pure substance, not a mixture. It is a homogeneous compound composed of carbon and sulfur atoms in a fixed ratio.
Sulphur is insoluble in water but soluble in carbon disulphide.