0
You can try following the water lines back to the water heater to make sure there is not a valve closed holding the water back that may have been forgotten after the repair. This being the case, I would be worried that the repair was not check to see if it was done correctly.If you have pressure on the hot water at other faucets in the home, then I would think this could be the problem. Need more help contact me through my board and I will try to help.
What else can I help you with?
What happens if you heat a closed container?
Eventually it will explode because the heat causes the gas particles inside the container to accelerate and thus, create pressure by colliding with each other and the sides of the container. This pressure --> boom.
What happens if you increased the driving pressure?
Increasing the driving pressure in a system, such as in a fluid flow system, will result in an increase in the flow rate of the fluid. This is because a higher driving pressure provides more force to push the fluid through the system. However, it is important to ensure that the system can handle the increased pressure to prevent any damage or failures.
What is the effect of pressure on boiling point of butane?
If nonsalt water is placed in a closed system (for example an automotive cooling system) then for every pound of pressure the system can handle (ex. radiator cap) the boiling point of water (normally being 212f) is raised by 3 degrees. Thus, if said system can handle only 1 pound pressure before the water boils the temperature of the water when it boils should be 215F. Or so I understand.
What is the pressure of chlorine inside a chlorine tonner in India?
The pressure inside a chlorine tonner in India will vary depending on factors such as temperature, volume of chlorine, and whether the tonner is sealed or connected to a supply system. Typically, the pressure can range from 100 to 300 pounds per square inch (psi). It is important to handle chlorine tonners with caution due to the high pressure and toxic nature of the gas.
Why hp detergent is used on particular washers?
HP (High Pressure) detergent is used on specific washers designed to handle high-pressure cleaning applications, such as industrial pressure washers. These detergents are formulated to effectively break down tough grease, dirt, and grime that regular detergents may not be able to remove under high pressure. They are also designed to work efficiently with the high-pressure systems to ensure optimal cleaning results.
Why is my bathtub handle leaking and how can I fix it?
Your bathtub handle may be leaking due to a worn out or damaged washer or O-ring inside the handle. To fix it, you can try tightening the handle or replacing the washer or O-ring. If the leak persists, you may need to call a plumber for further assistance.
What is the best way to repair a broken bathtub handle?
The best way to repair a broken bathtub handle is to first identify the cause of the breakage, then purchase a replacement handle that matches the make and model of your bathtub. Next, follow the manufacturer's instructions to remove the old handle and install the new one securely. If you are unsure or uncomfortable with the repair process, it is recommended to seek the help of a professional plumber.
What are some common issues that can occur with a bathtub faucet?
Common issues that can occur with a bathtub faucet include leaks, low water pressure, dripping, difficulty in turning the handle, and rust or corrosion.
What is the best way to repair a broken bath tub handle?
The best way to repair a broken bathtub handle is to first identify the type of handle and then purchase a replacement part. Once you have the new handle, follow the manufacturer's instructions to remove the old handle and install the new one securely. If you are unsure or uncomfortable with the repair, it is best to seek the help of a professional plumber.
How can I find a kitchen faucet that is specifically designed to handle high water pressure?
To find a kitchen faucet that can handle high water pressure, look for models labeled as "high water pressure resistant" or "designed for high pressure systems." You can also consult with a plumber or visit a specialty plumbing store for recommendations.
How can I go about replacing a bathtub handle?
To replace a bathtub handle, you will need to first turn off the water supply to the bathtub. Then, remove the existing handle by unscrewing it or prying it off. Next, install the new handle by following the manufacturer's instructions. Finally, turn the water supply back on and test the new handle to ensure it is working properly.
On the shower handle of a U.S. bathtub what does the C stand for?
Cold
How can I replace a bathtub handle?
To replace a bathtub handle, first turn off the water supply. Remove the old handle by unscrewing it and pulling it off. Install the new handle by following the manufacturer's instructions. Make sure it is securely attached before turning the water back on.
How can I repair a two-handle Delta bathtub faucet?
To repair a two-handle Delta bathtub faucet, you can start by turning off the water supply to the faucet. Then, remove the handles and the trim to access the cartridge. Inspect the cartridge for any damage or wear and replace it if necessary. Clean any debris or mineral buildup from the faucet components. Reassemble the faucet and test it to ensure it is working properly. If the issue persists, consider contacting a professional plumber for further assistance.
How can I replace a bathtub handle stem?
To replace a bathtub handle stem, you will need to turn off the water supply, remove the handle, unscrew the stem assembly, and install the new stem. Be sure to follow the manufacturer's instructions and use the correct tools for the job.
How can I repair a bathtub water valve that is leaking?
To repair a leaking bathtub water valve, you can start by turning off the water supply to the valve. Next, remove the handle and trim to access the valve cartridge. Inspect the cartridge for any damage or wear and replace it if necessary. Reassemble the valve and test for leaks. If the issue persists, you may need to call a professional plumber for further assistance.
Why is my bathtub faucet leaking from the handle?
Your bathtub faucet may be leaking from the handle due to a worn-out or damaged washer or O-ring inside the faucet handle. This can cause water to seep out when the faucet is turned on. It is recommended to replace the washer or O-ring to fix the leak.
