Ceramic tile can be installed over any non-compressible solid, non-flexible surface, but in areas of high moisture or possible water penetration, a cementious or water impermeable backer should be used to prevent rot.
Once concrete is cracked, there is no way to effect a real repair. You can use sealant to fill the cracks in, however. To do this, remove every speck of dust and debris from all the cracks, finishing with a hard blast of water. Let dry thoroughly, then fill in the cracks with Sonolastic NP-1 in silver-gray or limestone color, strictly following manufacturer's instructions. Pick the color that best matches your concrete. Do not substitute for the Sonolastic NP-1 . . . it is a proven, industrial strength product. If the cracks are deeper than 1 inch, tamp in some backer rod so that you have about a 3/4 inch crack depth to caulk. Backer rod is a round hard foam that comes in various diameters and lengths. The backer rod should be a little larger than the cracks are wide. You will probably have to buy several sizes to fit all your cracks. Do not caulk over the top of your concrete, just fill the cracks to the top.
You can, but you want to be sure the ceramic tile is not cracked or broken, make sure it is even, and not loose. It is reccomended that you you always remove any old tile before tiling. You can always lay a subfloor on top of the old tile to ensure your new tile was crack or pop out.
You did not mention if the three-quarter inch stuff was T&G (tounge and grove), that might make a little difference. I am not an expert in this area but have some personal experiences to share. I was allways told from old school you should have two layers of half inch material one layer turned ninety degrees from the other to give a solid one inch floor. Then you could use the one quarter backerboard and end up with a good tile floor. Then the new school came along and told me i could use one quarter over the T&G three quarter. They said the three quarter T&G was equal to the old style one inch. I tried it with the three quarter and i have several grout cracks and two broken tiles. I was using one quarter quarry tiles six by six. Have now fixed yet but in another room i used three quarter T&G plus another one half inch plywood then one half inch backerboard and same tiles no cracks.
It is best to remove the vinyl tile. If it is not on cement and is on wood you can install cement backer board. Be sure to put thin set under the board. If you spend the money and time to install ceramic tile and the vinyl tile comes loose all that $ is down the drain What is the best tile cement to use and this cement tile can be installed on vinyl tile and install ceramic tile on it
Yes on wood, no on smooth solid concrete
Yes it can. That seems a very satisfactory way to do it.
Concrete backer board is usually used as an under layment for ceramic tile. It can be used on walls, floors or countertops. It has a solid core and is faced on both sides with fiberglass. It's an ideal under layment for wet areas like shower walls and bathtub surrounds, and is typically mold resitant.
It is best to remove the vinyl tile. If it is not on cement and is on wood you can install cement backer board. Be sure to put thin set under the board. If you spend the money and time to install ceramic tile and the vinyl tile comes loose all that $ is down the drain What is the best tile cement to use and this cement tile can be installed on vinyl tile and install ceramic tile on it
If you are talking about a fiber cement backer board, the manufacturer of the board should provide the answer you are after. I am currently using Hardiplank to reside my house, and the manufacturer recommends attacheing the TyVek house wrap to the wood sheathing per TyVeks recommended process. Hope this helps.
a concrete or masonry blade
The purpose of using cabinet backer board in kitchen renovations is to provide a stable and durable surface for attaching cabinets to the wall, ensuring they are securely installed and can support the weight of the cabinets and their contents.
broadway backer
Pull it off with pliers if that's easy. If not, cut out the backer board and renew it. It should be done when new tiles are done anyway. Use a fibre or concrete backer board, NOT wallboard.
The best type of underlayment for tile on concrete surfaces is a cement backer board. It provides a stable and moisture-resistant base for the tile installation, ensuring durability and longevity.
Wally De Backer's birth name is Wouter De Backer.
The best practices for installing shower backer board to ensure a waterproof and durable shower enclosure include properly sealing seams and corners with waterproof tape or sealant, using corrosion-resistant screws to secure the backer board, and ensuring the backer board is installed over a waterproof membrane. Additionally, it is important to follow manufacturer guidelines and recommendations for installation to achieve the best results.