0
Difference between ultimate strength design and working stress design?
Wiki User
∙ 11y ago
Working stress method of design based on the elastic theory in which materials, concrete and steel are assumed to be stressed well below their elastic limit under the design loads. Working stressess (permissible stress) for the materials are determined by dividing the ultimate or yield stressess by suitable factor of safety values.
Limit state method of design based on limit state concept, te structure shall be designed to withstand safely all loads liable to act on it throughout its life;It shall also satisfy the serviceability requirements, such as limitations on deflection and cracking. The acceptable limit for the safety and serviceability requirements before failure occurs is called a "limit state". The aim of design is to achieve acceptable probabilities that the structure will not become unfit for the use for which is intended, that is that it will not reach a limit state...
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the difference between estimating and tendering in the construction trade?
The process of cost estimating is working out how much a building or other construction will cost to make. The costs are usually divided into materials and labor costs. Tendering is the process of making a priced offer to construct the building. This is a legally enforcable offer made within the conditions of the tender documentation.
What materials do masons work with?
The masons use building material for working and also mortar make by mixing cement sand and water that he put between line of bricks stones or marble.
What is the Test Procedure to Determine Compressive strength of Hollow Blocks?
Testing the compressive strength of hollow blocks typically follows a standard procedure to ensure accurate and reliable results. Here's a general outline of the test procedure: **Sample Preparation:** Select representative samples of hollow blocks from the production batch. Ensure the samples are free from defects and have been cured appropriately. **Conditioning:** If the blocks are not already at room temperature, allow them to acclimate to the testing environment. **Equipment Setup:** Set up the compression testing machine according to standards or specifications. Ensure the machine is calibrated and in good working condition. **Sample Identification:** Mark each sample with a unique identifier for accurate tracking of results. **Moisture Content Check (if applicable):** Determine and record the moisture content of the samples, especially if it can affect the compressive strength. **Testing Procedure:** Place the hollow block specimen on the compression testing machine. Align the specimen so that the load is applied evenly on the blocks. Gradually apply a compressive load at a uniform rate until failure occurs. Record the maximum load at failure and note any signs of distress in the specimen. **Calculation of Compressive Strength:** Calculate the compressive strength using the formula: Compressive Strength = Maximum Load / Cross-sectional Area of the Block. **Reporting:** Document all relevant information, including sample identification, moisture content, and compressive strength values. Prepare a test report with details of the testing procedure, equipment used, and results obtained. **Quality Control:** Compare the results with specified standards or requirements to ensure the hollow blocks meet the desired compressive strength. **Data Analysis:** Analyze the data for any trends, variations, or anomalies that may indicate issues with the production process. **Documentation and Archiving:** Keep a record of the test results and associated documentation for future reference or quality control purposes. It's crucial to follow specific standards or guidelines relevant to the type of hollow blocks being tested, as procedures may vary based on factors such as block dimensions, material composition, and testing conditions. Always adhere to industry standards or applicable building codes for accurate and meaningful results.
What is factor of safety in Crane load lifting?
If SLI is in operating condition then sLI itself will indicates that whether load is in safe mode. But if SLI is not working then one must be considered 40 % factor of safety of crane SWL and in SLI working condition it will be considered 20 % of its SWL.
What is 21 days strength of cement concrete?
concrete (cement) cures with age, well at least up to a point. think of breaking up the concrete slab that was cast yesterday evening, versus a concrete slab that is a year old. the optimum strenght of concrete (maximum strenght it is assumed to reach) is statistically reached after 28 days, if proper and adequate curing took place, and normal working / exposure conditions and control of quality took place. Curing is basically protection against severe exposures as draft winds that may cause cracking, and keeping the surface moist over the 7 days, by covering it with DPC plastic or regular sprinkling with water. after only 7 days of curing, the 28 day strenght can be accurately predicted to determine if it will pass the requirements. after 7 days (I have also seen 24hrs samples) a cube sample is crushed to determine the 7 day crushing strength. this sample was then cast at the same time as the structure being assessed. the 7 day strenght is measured in Mega Pascals (Mpa) or equivalent units Kilo Newton per square millimeter (kN/mm2) and really depends on the application the concrete is used for: walkways will probably be 10Mpa single storey building footings and floor slabs, say 15Mpa floor slabs where vehicles may drive could be even 35Mpa. Suspended slabs, like first floor slabs etc, say 40Mpa.
What is the difference between a hypothesis and a working hypothesis?
The difference is that working hypothesis is that your still working on it but the hypothesis that your not working on it.
Difference between temporary and permanent working capital?
difference between temporary and permanent working capital needs
Difference between multistore and working model memory?
what is the difference between the memory store model and the working memory model?
What are the Advantages and disadvantages of working stress design and ultimate strength design?
Ultimate strength design assumes the entire cross section of a member is subjected to its yield stress and will generally save material, but be less conservative given the same factor of safety.
What is difference between gross working capital and net working capital?
Gross working capital is the amount company invested in current assets while net working capital is the difference between current assets and current liabilities.
What is the difference between a working mother and a nonworking mother?
a working mother has more responsibilities
What is the difference between has been working and is been working?
It means that that person was working the other one means they are working right now
What is the difference between a hard working man and a hard-working man?
Sasquatch has been sighted
Difference between working drawing and 3d model and sketch?
the difference is stechn is when its light drawn is when its dark!!
What is the difference between organs and systems tissues?
The difference between organ system and tissue is that organs are made of many layers of tissue working together and a organ system is many organs working together as a system.
What is the ultimate stress of mild steel?
Allowable stress would normally refer to design using Allowable Strength Design, also known as working strength design. In this the allowable stress is usually a fraction of the yield strength and can be different for uniform tension and bending. Typically mild steel has a yield strength of about fy=250MPa with allowable stresses in Tension, 0.6fy=150MPa Bending, 0.66fy=165MPa
What is the difference between entrepreneur and an employer?
The difference between the two is a entrepreneur is the owner of a company, and a employer is working for someone. Entrepreneur is the launcher, organisor and owner of a company.
