It starts curing the second they put water in it.
Yes. Water is actually needed for concrete to set and is vital to the curing process. Concrete will set just fine under water. Depending on your specific application (will all of the pour be under water or will it start under water and finish above the water line) you may need to adjust the initial dryness of the mix as well as take more care in the pour. All of the volume of the concrete that is under water shoudl be poured in continuous fashtion. If you must pour in steps, the start of the next pour must be "in" the old pour so as to not leave a water survice between the pours. This "seam" will tend to stay and produce a weaker stucture.
As soon as the Cement comes into contact with water. This will start as soon as the cement and aggregates come into contact unless the aggregates have been dried of all surface water.
Under reinforced is that in which provided steel ratio is less than balanced steel ratio. Concrete beams are designed as under reinforced beams. The reason is that the failure start by yielding of steel instead of crushing of concrete. Mian Yaqoob
Yes it will crack. I think any and all concrete will crack. Maybe not enough to leak water but hairline cracks. Coat your pool with good waterproof sealant if leaks start.
It depends on the design life [50 -75 years?], the environmental & service conditions, and preventative maintenance practices. Concrete is thought of as being permanent strong and very durable. In actuality it is a very complex, thermodynamically unstable and chemically reactive building material that continues to cure and become stronger for years. It is also vulnerable to many external influences! To obtain maximum life cycle [make it last] there are dozens of protective measures that can be taken to make it Green. An understanding that concretes absorb water and expel internal chemistry for years is paramount to obtaining a long life. That drop of water you put on the surface was absorbed into the interior through the Gel-Pore / Capillary System, present in all concretes. This path is formed when water in the mix comes to the surface during the initial set/curing phase [Bleed Water]. After curing, it's hard, we walk and drive on it, but water we put on the surface is absorbed back into it. This moisture carries contaminates: salts, acidic compounds and carbon dioxide to the interior. Lowering the High pH around steel reinforcement to a point that corrosion cells begin to form on the embedded steel in the matrix. Internal chemistry allowed to migrate out to the atmosphere on the surface results in several deleterious conditions. ASR, efflorescence, ettringite are a few! This is also what blisters or "Burns" a coating off in a very short time. A paint designed to protect the concrete, doesn't stand a chance if alkali is coming to the surface to compromise the bond! First step in obtaining a long lasting concrete is to Stabilize It by waterproofing, to fill the microscopic voids in the capillary system. Nothing going in and nothing coming out of it is a Great Start. In reducing Moisture and Oxygen content inside a concrete, you have eliminated two of the four conditions needed for corrosion to commence. A stabilized concrete will give longevity to this very volatile building material, make it Green and prolong it's service life substantially. Answer is: " It Depends On How You Treat It!"
You should start watering concrete within the first 24 hours after it has been poured to ensure proper curing. This helps prevent cracking and strengthens the concrete.
To pour a concrete slab effectively and efficiently, start by preparing the site by leveling the ground and setting up formwork. Next, mix the concrete according to the instructions and pour it into the formwork. Use a screed board to level the concrete and a bull float to smooth the surface. Finish by adding control joints and curing the slab properly by keeping it moist for several days.
To safely and effectively perform plastic casting at home, you should start by choosing a well-ventilated area and wearing protective gear such as gloves and a mask. Follow the instructions on the plastic casting kit carefully, including mixing the materials in the correct proportions and allowing for proper curing time. Make sure to clean up any spills immediately and dispose of waste materials properly.
April 2011
Concrete nouns that start with X are:xylophonex-ray machinex-ray fishXerox copy
You can. You start by applying moisture barrier to the concrete--flooring stores have it--then gluing the hardwood to the concrete.
Yes. Water is actually needed for concrete to set and is vital to the curing process. Concrete will set just fine under water. Depending on your specific application (will all of the pour be under water or will it start under water and finish above the water line) you may need to adjust the initial dryness of the mix as well as take more care in the pour. All of the volume of the concrete that is under water shoudl be poured in continuous fashtion. If you must pour in steps, the start of the next pour must be "in" the old pour so as to not leave a water survice between the pours. This "seam" will tend to stay and produce a weaker stucture.
In August 2008. It didn't take them very long.
The initial setting time of cement is 30 minutesThe final setting time of the cement is 10 hours.The initial and final setting time of the cement can be found by using the Vicat's apparatus.
Actually, the casting director for the maximum ride movie hasn't been chosen yet. So until the producer finds a casting director, the auditions have not been placed. I think they may start casting people by next year.
Excess water (over hydration) causes weak concrete. The water in concrete is there to start a chemical process which results in the hardening process. The excess water is not used in the chemical process and results in a weakened concrete.
To install a concrete mailbox post effectively, start by digging a hole that is at least 24 inches deep and wider than the post. Place the post in the hole and fill it with concrete mix, making sure it is level and plumb. Allow the concrete to set for at least 24 hours before attaching the mailbox. Additionally, consider adding gravel at the bottom of the hole for drainage and using a post level to ensure the post is straight.