0
Density of brick bat coba
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Is codes on Brick Bat Coba?
No, Integral WP admixture which is added in coba mortar has IS2645, but lonely coba has not any IS codes. Hassan 09889987866
What is the Difference between IPS and Plain Concrete Cement Flooring?
how is conventional brick bat coba work done
What is the Cement consumption for brick bat coba?
Water proofing treatment with 50mm thick screed in cm(1:5),115(thick brick bat in cm (1:3, third layer or 25thick in 33(1:3)=1.18 bags per sequre meter
What is the full form of BBLC in civil line engineering?
Brick Bat Lime Concrete
Is codes on Brick Bat Coba?
No, Integral WP admixture which is added in coba mortar has IS2645, but lonely coba has not any IS codes. Hassan 09889987866
What is the Difference between IPS and Plain Concrete Cement Flooring?
how is conventional brick bat coba work done
What is the Cement consumption for brick bat coba?
Water proofing treatment with 50mm thick screed in cm(1:5),115(thick brick bat in cm (1:3, third layer or 25thick in 33(1:3)=1.18 bags per sequre meter
What are the Disadvantages of Brickbat Coba?
1. Brickbat coba will have lot of surface cracks and hence it is not a waterproofing system. 2. The quality of bricks used in BBC is usually of not a good quality hence over a period of time they absorb water and become loose and give way to more leakages. 3. Brick bat coba should not be confused for waterproofing. It is a good wheather proof layer.
Why is half a brick called a bat?
Because half a brick weighs the same amount as the average bat
What is brick bat coba?
Water proofing with Brick bat Coba by Exposing the RCC Slab to its bare Surface, Clearing the Surface of all Lose Particles and Dust, Carting away of debris and Spreading neat Cement Slurry mixed with waterproofing Compound on the Cleaned Surface, filling up the uneven Surface, honey Combing etc. Spreading of CM(1:5) mix, mixed with Water proofing Compound and Grouting brick bat in the Mortar with Necessary Slope of approx. 1 in 100 for Easy flow of Water. Filling the Joints in the bricks with the Mortar properly. This treatment to Continue along the inner Side of the Parapet or other Adjoining Walls up to a height of 30 cm in the Shape of a round Vatta and finally Converting the top Surface with Jointless Waterproofing Cement Sand Mortar 1:4, 20 to 25 mm thick finished Smooth with Trowel in Cement Colour marked into 30cms x 30 cms False Squares. The Average thickness of Complete treatment shall be 100mm. Curing to be Continuously done for Surface.
What is half a brick called?
Bat
What are the release dates for Bat Masterson - 1958 The Marble Slab 3-31?
Bat Masterson - 1958 The Marble Slab 3-31 was released on: USA: 11 May 1961
How to Waterproof Toilets & Bathroom in 14 Steps?
Steps for Waterproofing Bathroom/Toilet: Step 1. Remove the existing W.C. pan tiles etc and break open the exciting brick bat coba and I.P.S toilet/bathroom and reach the bare slab. Step 2. Moisten the crack and apply a Bonding Coat of POLYALK EP and cement slurry in the ratio of 1:0.5 in the groove Step 3. Within 30 minutes of application of Bonding Coat. Prepare and apply by hand POLYMER MODIFIED MORTAR using 2 Kg POLYALK EP, 5 Kg cement, 15 Kg graded quartz sand. DO NOT ADD ANY WATER TO THIS MORTAR. This has to be a wet-on application. Step 4. Air Cure the surface for 48 Hrs Step 5. Sprinkle Water for 3-4 days Step 6. Clean the slab of all dust, dirt oil, grease, grime, etc. Step 7. Drill holes in the slab and fix nipples and inject grout by mixing 5% of POLYALK EP and POLYTANCRETE NGT@150mls both per bag of cement. Add water as a minimum for flowability. After grouting is completed cut and seal the nipples by Polymer Modified Mortar. Step 8. Prepare a slurry using 1 Kg of POLYALK WP and 0.25 Kg of cement and apply by brush on the bare slab. Mixing should be done using a low-speed stirrer to form a lump-free consistency. NO WATER TO BE ADDED PREPARE AS MUCH SLURRY AS CAN BE USED IN 30 MINUTES. Step 9. After 24 hours, apply a second coat of similar slurry of the same proportion. Step 10. Air Cure the surface for 48 Hrs. Step 11. Cure the coating with damp gunny bags for 4-5 days. Step 12. Apply the third coat of slurry using 1 Kg of POLYALK WP and 0.25 Kg of Cement and apply by brush on the second coat. NO WATER IS TO BE ADDED. Step 13. While this coat is wet and tacky lay the cement mortar for providing brick bat coba. This has to be a wet-on-wet application. Add SUNPLEX (330 gms pouch) per 50 Kgs bag of cement in the mortar mix for brick bat coba. Step 14. Proceed with providing conventional brick bat coba. I.P.S over the slab and fix tiles/pan as per requirement. Add SUNPLEX (330 gms) pouch in the cement mortar mix of the I.P.S to minimize the shrinkage cracks on the IPS.
How many ounces is -2 bat?
That would depend on the length of the bat. The '-2' is known as the 'bat drop' or 'drop weight' and means that the weight of the bat, in ounces, is 2 less than the length of the bat in inches. To find the weight of the bat you must first measure the bat to find its length. If the length of the bat is 30 inches, the weight of the bat is 28 ounces. If the length of the bat is 28 inches, the weight of the bat is 26 ounces.
What does -3 mean on a baseball bat?
The weight of the bat, in ounces, is 3 less than the length of the bat in inches. The -3 is called the 'bat drop' or 'drop weight'. Measure the bat and then subtract 3 from the number of inches and you will determine the weight of the bat in ounces. If the length of the bat is 30 inches, the weight is 27 ounces. If the length of the bat is 33 inches, the weight is 30 ounces. If you see a bat with a -6 on it, that means the weight of the bat, in ounces, is 6 less than the length of the bat in inches ... a -8 means the weight, in ounces, is 8 less than the length of the bat in inches.
What is a -3 baseball bat?
A -3 Bat is a bat where the weight is equal to the height minus 3 So if you had a 34 inch bat, the weight would be 31 oz.
