0
What else can I help you with?
How do you cover brick with concrete?
POUR THE CONCRETE OVER THE BRICK
Can concrete set under water?
Yes. Water is actually needed for concrete to set and is vital to the curing process. Concrete will set just fine under water. Depending on your specific application (will all of the pour be under water or will it start under water and finish above the water line) you may need to adjust the initial dryness of the mix as well as take more care in the pour. All of the volume of the concrete that is under water shoudl be poured in continuous fashtion. If you must pour in steps, the start of the next pour must be "in" the old pour so as to not leave a water survice between the pours. This "seam" will tend to stay and produce a weaker stucture.
What is pour card in civil engineering?
In larger concrete projects with a good quality control program, a pour card is a document that describes the location of the concrete being poured, type/specification of concrete being supplied, a signature block by the inspector and/or engineer indicating that the rebar has been inspected in-place and approved, date of pour, serial number of the concrete truck(s) supplying the concrete, sign-off by the inspector indicating on-site tests for slump and air entrainment (if required) have been completed. Temperature, weather and ticket info from the concrete batch plant/delivery truck are also recorded. The contractor's quality assurance manager will typically keep all the pour cards for a project on file, especially in the even that subsequent testing indicates substandard concrete was installed.
Can you pour concrete to steel bars painted with red oxide primer?
No, it is not recommended to pour concrete directly onto steel bars painted with red oxide primer. The primer may prevent proper adhesion between the concrete and the steel, leading to a weaker bond and potential structural issues. It is important to remove any paint or primer from the steel bars before pouring concrete to ensure a strong and durable connection between the two materials.
How much should it cost to pour a concrete sidewalk Memphis TN?
In Memphis, TN the cost of having a professional contractor pour concrete on a driveway averages from $5 to $9 per square foot. The addition of a sealant to preserve a driveway can cost as much as $18 per square foot in Memphis, TN.
Do you need a license to pour concrete?
Yes
Can you pour concrete over asphalt?
Yes, but you will need to reinforce with a wire mesh and then pour.
How do you properly prepare and pour a concrete slab?
To properly prepare and pour a concrete slab, you need to start by clearing and leveling the area where the slab will be poured. Next, create a formwork to contain the concrete. Then, mix the concrete according to the instructions, making sure it has the right consistency. Pour the concrete into the formwork and use a screed to level and smooth the surface. Finally, let the concrete cure and set before removing the formwork.
How much does it cost to pour a concrete driveway?
how much does it cost to form and pour concrete in Mobile, AL
Can you pour concrete on old concrete?
not normally. it depends on what you are trying to accomplish. if you need a thin layer than you can pour a thin set layer which hardens and adheres better than concrete. if the added part is thicker you can drill holes in the old and put re bar in then pour on top to help tie the two together.
How much to pour a concrete slab 12x24?
about how much to pour a concrete slaba 12 x 14'
Can you pour concrete over existing rock?
Concrete need a uniform and compacted base, so as long as that rock is uniform and compacted, you should be fine.
How do you cover brick with concrete?
POUR THE CONCRETE OVER THE BRICK
How to prepare the ground to pour a concrete curb?
There are a number of ways in which you could prepare the ground to pour a concrete curb. You could level the surface and pour sand.
How do you properly prepare and pour concrete for a new driveway?
To properly prepare and pour concrete for a new driveway, you need to start by excavating the area, creating a solid base, and setting up forms to contain the concrete. Next, mix the concrete according to the instructions, pour it into the forms, and level it with a screed. Finish by smoothing the surface with a float and adding any desired textures or patterns. Allow the concrete to cure properly before using the driveway.
How much concrete do you need to pour in a floor measuring 28 feet wide 72 feet long and 6 inches deep?
you would need 37.33 yards of concrete or 38 to be safe
How to pour a concrete pad correctly?
To pour a concrete pad correctly, first, prepare the site by leveling the ground and creating a form to contain the concrete. Next, mix the concrete according to the instructions and pour it into the form. Use a screed to level the concrete and a float to smooth the surface. Allow the concrete to cure for the recommended time before removing the form.
