0
What else can I help you with?
What is the value of a Roy Rogers and Trigger lamp from Plasto Manufacturing in Chicago without a shade?
I just saw a roy rogers and trigger lamp from plasto mfr. going for $450, on the RubyLane antiques website. This lamp was 15 and 1/2" tall and wasn't very colorful. My lamp is smaller, but really bright, with lots of colors, so I think, maybe it's worh more. Good luck!
What is the value of 1950's Plasto ceramic lamps?
Many of the lamps are worth prices close to $150 each. The exact price will depend upon the actual lamp and its condition.
How would you find out if this plasto mfg co lamp is worth?
Hi, I have Plasto Mfg Co table lamp I received in 1980. The name Glenn Richardson is stamped on the lamp. The base is shaped as a drum with three patriots two playing drums and one playing flute with a thirteen star American flag behind them. The shade is dark blue with small red and white stars. Might this be worth more than the $20 my daughter wants to sell it for at our yard sale? Any assistance would be appreciated. Thank you, Michael Rakus (mrakus617@hotmail.com)
What words can I use to describe lantern?
bright,colourful, maybe something to describe its pattern portable light, lamp, kerosene lamp, oil lamp
Infocus lp640 lamp wont strike with good bulb?
If the Infocus LP640 lamp won't strike with a good bulb, it may be due to an issue with the lamp ballast or power supply. Check the connections and make sure they are secure. If the issue persists, it may be necessary to replace the lamp ballast or seek professional assistance.
Why won't the wax in my lava lamp melt?
If the lava lamp wax is not melting, it may be due to the bulb not providing enough heat. Ensure that the lamp is plugged in and turned on for sufficient time to allow the wax to melt. If the issue persists, the lamp may be defective and need to be replaced or repaired.
Why does the View Sonic PJ400 projector Lamp light blink but the projector will not turn on?
Whenever most projectors flash the lamp status light, but nothing happens, it is usually a circuit board issue.I personally have had the same issue before. The lamp was brand new, but it turned out being the projector and not the lamp.If, however, it may not be a circuit board issue, it could be your lamp. If you have used your lamp over 1000 hours, it's probably it.Contact ViewSonic Customer Service to schedule a repair, or to get price quotes.
Why is the USB port on my lamp not working?
The USB port on your lamp may not be working due to a faulty connection, a damaged port, or a power supply issue. It is recommended to check the port for any physical damage, try using a different USB cable or device to test the port, and ensure that the lamp is receiving power properly. If the issue persists, it may require professional repair or replacement.
Why is my lamp flickering?
Your lamp may be flickering due to a loose bulb, a faulty socket, or a problem with the electrical wiring. It is important to address this issue promptly to prevent any potential safety hazards.
What is heated by the thermal energy wasted by Portable Radio?
The surrounding environment, such as the air and nearby surfaces, is heated by the thermal energy wasted by a portable radio. This is because the radio emits heat as a byproduct of its operation, which can raise the temperature of its immediate surroundings.
Why is my lamp flickering and how can I fix it?
Your lamp may be flickering due to a loose bulb, faulty wiring, or a problem with the lamp socket. To fix it, try tightening the bulb, checking the wiring for any damage, and ensuring the socket is secure. If the issue persists, consider replacing the bulb or seeking professional help to inspect and repair the lamp.
Why wouldn't the lamp turn on?
The lamp may not be turning on because the bulb is burnt out, the power source is disconnected, or there could be a faulty switch or wiring issue. It is important to check these components to determine the cause of the problem.
