0
What else can I help you with?
Dodge sprinter Engine control unit indicator lamp came on when I was leaving engine run after installing a recently charged battery shut off engine and restarted lamp came on momentarily then went off?
You need to have it checked for trouble codes.
Why does your engine control unit indicator lamp on your 2006 Sprinter stay on?
The engine control unit (ECU) indicator lamp on your 2006 Sprinter may stay on due to various issues, such as a malfunctioning sensor, a problem with the emissions system, or a fault in the engine management system. It could also indicate a stored trouble code that needs to be diagnosed with a scanner. Ignoring the light can lead to reduced performance or increased emissions, so it's advisable to have the vehicle checked by a professional mechanic.
How do you Fiat doblo service and oilchange light reset?
according to autodata service lamp can only be reset using suitable diagnostic computer Dr.Pedro VolksWagen service technician
Reset the service indicator lamp on opel combo?
with the switch off, press and hold the odometer button. Turn the switch on, and the odometer will be in insp mode. mode. Press the odometer button until the indicator shows --- . Turn the switch off and the lamp should be reset.
How do you remove rear tail light on 08 dodge sprinter van?
2008 Dodge Sprinter 2500 tail light bulb lamp replacement procedure: Purchase the correct replacement tail light bulb(s) first, before disassembling the vehicle. See Sources and Related Links below for replacement bulb information and full light bulb part numbers list. Then consult your owner's manual for the tail light bulb lamp replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
How do you reset lamp hours on a Toshiba TLP-XD2000?
To reset the lamp hours on a Toshiba TLP-XD2000 projector, first ensure the projector is powered on. Navigate to the "Lamp" menu using the remote or the projector's control panel, then select the option to reset the lamp hours. Confirm the reset when prompted, and the lamp hour counter will be set back to zero. Be sure to check the user manual for specific button sequences, as they may vary.
How do you reset the oil change lamp on a 2007 town and country?
To reset the oil change lamp on a 2007 Town and Country, locate the reset button on the instrument panel. Hold the button down for 5 seconds.
How can you reset your maintenance reminder light on your 1995 Ram 3500?
The SRI lamp may only be reset with the use of a DRBII scan tool, or equivalent. If this is not available, you will have to take the vehicle to a properly equipped shop for them to reset the lamp.
How do you reset the service light on an Opel Corsa 2005 1.6 Sport?
There's no great ''trade secret'' as to how to reset the service indicator lamp on most Vauxhall's, simply refer to pages in the Owner's Handbook! For reference of those interested in such matters, but who might not have access to an owner's manual, this is the procedure to follow: Vauxhall service reset * Turn Ignition Off * Hold Trip Reset In * Turn Ignition On Still Holding * Trip Reset wait for three dashes * Turn off Ignition * Turn on Ignition to confirm To the best of my knowledge, the above service light reset procedure applicable to most Vauxhalls HOPE THIS SAVES YOU PAYING FOR INFORMATION!!!!!!!!!!!!!!!!!!!! ;-)
Why doesnt brake lamp failure lamp on dash of 94 Honda Accord not reset after bulb replacement?
Remove the negative battery terminal (-) for about 15 minutes and most codes will reset.
How do you reset service indicator on2009 jaguar xf?
> Resetting service reminder: 1. Press and hold rear fog lamp switch 2. Turn ignition on, do not start engine 3. Release rear fog lamp switch 4. Press and hold trip button (end of left side stalk) 5. Press and hold rear fog lamp switch 6. See "Resetting Service Light" message in message center
How do you reset a engine warning lamp on a Hino 500 series truck?
To reset the engine warning lamp on a Hino 500 series truck, first, ensure that the underlying issue causing the warning has been resolved. Then, use a diagnostic scan tool to clear the fault codes stored in the engine control unit (ECU). If a scan tool is not available, disconnect the truck's battery for about 10-15 minutes, which may also reset the lamp. Always consult the vehicle's service manual for specific procedures and precautions.
