answersLogoWhite

0

No you can not.

User Avatar

Wiki User

∙ 12y ago
User Avatar

What else can I help you with?

Continue Learning about Computer Science

What is the black foam cover on a microphone called?

pop filter


Will stryfoam survive 1000 degrees?

maybe up to 120, at the most, because i burned through a solid block of foam using a soldering iron.


What is the function of the floor screed?

The function of floor screed is to make a structural level floor surface above a waterproof membrane. It is usually made by either pumping in a special mix of self- levelling runny 'concrete - like' material or more traditionally a sharp sand and cement mix. Traditional screed is tamped by a large flat wooden or aluminum beam, which is called a screed, from which screed gets it's name. It should be very flat once finished and can be tiled once it has dried out, which can take weeks. It is usually laid over an insulation foam and often has electric heating elements or warm water pipes in it to make it into a large radiator. Thin screed needs to be reinforced to make it strong enough for the loads that are put on top of it which can be steel mesh or special fibres. This means that thinner screeds are often made up of specialist ingredients to make them self levelling and strong.


What is elapor?

Elapor is a kind of foam, similar polystyrene and used to make packing elements for electrical items. It is made from small beads that are placed in a mold and then expanded to form the shape of the mold. Elapor is also a popular material with which to manufacture remote control aircraft, due to its durability. If crushed, elapor can be made to re expand to near its original shape by immersing it in, or pouring over it, boiling water.


How water can be modified by additives to improve fire-fighting performance?

Additives are used in fighting fires because some classes of fires do not respond well when plain water is used to try and extinguish them. In fact, in some classes of fire, water actually makes things worse. The best example of this are Class B fires (Flammable Liquids like Gas and Oil).The 3 things needed for fire combustion to sustain itself are Heat, Oxygen, and Fuel (the Fire Triangle). Removal of any one element in the triangle will stop combustion. The aim of all firefighting additives is to remove one or more of those elements. Since it is difficult or impossible in many cases to remove the source fueling the fire, most additives are focused on removing heat and/or oxygen from the fire to halt combustion.While there are many water additives, the most well-known example is AFFF.Aqueous Film Forming Foams (AFFF) is awater based foam that is used on Class B (flammable liguid) fires. It's commonly used in airport firefighting vehicles as fuel fires are very difficult to extinguish. The foam expands rapidly when it hits the air, coats the surface of the fuel causing the fire, thus cutting off oxygen. It also cools it, thus taking away heat.Alcohol Resistant Aqueous Film Forming Foams(AR-AFFF)These are other types of foam that are used on alcohol type fires

Related Questions

Difference between gas concrete and foam concrete?

Gas concrete is also known as aerated concrete. It is generally made by introducing air or gas in to slurry composed of portland cement or lime and finely crushed silicious filters.Foam Concrete. A stabe foam is mixed with cement and crushed sand slurry thus causing the cellular structures when it gets set and hardened.


How could you make synthetic concrete foam agent with foam stabilizer?

hiu can use 3% sodium luaryl sulphate plus bone glue ,15


Influence of Cement Foaming Agent on the Quality of Foamed Concrete?

The influence of cement foaming agent on the quality of foam concrete is very important. A good cement foaming agent can make high-quality foamed concrete. The foam produced by high-quality cement foaming agent has good stability and can be constructed in a low temperature environment. The one-time pouring height is more than twice that of similar cement foaming agents.


Is egg white a good substitute of foam agent in foam concrete?

Egg white can serve as a substitute for a foam agent in foam concrete due to its protein content, which can help stabilize air bubbles and enhance the material's structure. However, its effectiveness may vary compared to traditional foam agents, as egg whites may not provide the same level of durability or consistency. Additionally, using egg whites could raise concerns about hygiene and longevity in construction applications. For optimal performance, conventional foam agents are generally recommended.


For lightweight foamed concrete how much foam is used in adequate mix of foam cement and water?

you can see the example : if you porduce 600kg/m3 foamed concrete ,you will need foaming agent about 0.5kg ,cement is 600kg, water is 300kg ,of course ,the density is lower ,the foaming agent need more ,the foam need more . we suggest you visit our website to read more information : httP://www.foamed.com.cn ,or send us email:heyimy@gmail.com


What are the commonly used methods for curing foam concrete?

Concrete recycling


What are the benefits of using foam for under concrete?

Using foam for under concrete provides benefits such as improved insulation, reduced weight on the structure, and increased resistance to moisture and mold.


What is the mix design for foam concrete?

1:1.5:0.4


Can you use ordinary washing powder for concrete foam?

yes


How do foam nozzles work?

Foam nozzles work by mixing water and a foaming agent under high pressure to produce foam. The foaming agent creates bubbles in the water stream, which expands the volume of the foam. This foam is then used for firefighting or cleaning, as it is more effective at smothering fires or clinging to surfaces.


What is the best mix design for foam concrete?

1:1.5:0.4


What is meant by Spray Foam Insulation Company?

PolyCo is a full-service spray foam insulation company offering cost-saving solutions to reduce and eliminate tripping hazards and associated liability. Insulation contractor staff is dedicated to helping residences, businesses, and municipalities improve their sidewalks and parking areas by eliminating uneven concrete without the traditional removal and replacement method. Polyco Spray foam insulation Baton Rouge eliminates costly concrete replacement and the disruption and inconvenience to your business and customers and help you comply with ADA standards. Contact us if you are looking for spray foam insulation companies near me Baton Rouge or concrete lefting near me. Concrete leveling Baton Rouge use concrete lifting foam kit for concrete lifting spray foam insulation Louisiana Contact Us: 225-247-2468