What I would do, although it's probably too late, is take the battery out and wait until everything dries off. I dont know how to fix one after it dried.
I agree with that comment if you can remove the battery right away. My son had gone swimming with it and once we came home it no longer worked. Then the battery went bad in it, so it was a mess. but it works fine! good luck!
Here is what I suggest, you have to remove the battery. Get the special screw driver to open the Ds and Pokewalker 360/x50. Open it up and carefully disconnect the display. This is a bit tricky if you have never done it before. there is a small black flap that presses the display belt onto the connection. You have to pull it up so it will release the belt (it has a hinge). Then take a qtip and alchohol and clean the board so that no residue is left on the board on either side. In particular by the battery if it went bad and the display belt. Then let it all dry. put on all 4 screws for the circuit board. Connect the belt by sliding it back into the socket and once securely in place, gently push the hinged flap back toward the belt put all your buttons and close it up. Secure the screws, place a new battery in the back. Now I had to push my buttons for a while before it started working (2 minutes).
Then I heard beeping and the screen came on.
To fix a pokewalker you might have to send it to Nintendo but if the game says a Pokemon is in the pokewalker and there is no Pokemon in the pokewalker press and hold up, select and R at the pokewalker connection screen. It will say "you will loose the ability to transfer any other Pokemon to the pokewalker". DO NOT WORRY. The Pokemon it says is in the pokewalker will just come back with no connection needed. you can now send Pokemon to the pokewalker again.
replace the battery and the battery has the numbers you need for the pokewalker
water on a dishtowel
yes somtimes i would prolly say it would 99% of the time
The Watts on a pokewalker are the "cash" for the pokewalker every 20 steps is about one watt every time you meet a certain amount of watts you unlock a new area for the pokewalker
It depends on what caused the device to not power on. The battery could be damaged. Replace the battery. The charging unit could be damaged. Replace the charging unit or find the damaged component and replace it. The charging connector could be damaged. Replace the circuit board or find the damaged component and replace it. The power button could be damaged. Replace the circuit board or find the damaged component and replace it. Something could have fried the circuit board. Replace the circuit board or find the damaged component and replace it.
No problem, If your phone has been damaged by water. Put your phone in sunlight for 2 or 3 hours, but make sure your phone's screen should not be to face of sun, because sunlight can damage screen's colors. Put that by backside to face of sun. Sunlight will dry the water. Then after 3 or 5 hours try to turn on it, If it is working then enjoy with that. I am sure it will work because it is my personal experience. If it is not working then I will suggest you that see your phone to a mobile engineer. He will dry the water by electric bulb or his instruments. But you don't try electric bulb, it can be harmful for your phone and you also. Hope this help, Saqib
Damaged frames are discarded. Retransmission - if needed - is handled by higher-layer protocols, like TCP.
You can't. Sorry!
buy a new one!
If the pokewalker gets wet I will try and take the battery out and dry it as much as i can, I am not that positive it will still work but hopefully it will.
Get a new one because you f’d up
no
The Pokemon is not actually 'in' the Pokewalker, it's still on the cartridge, just set aside. It no longer shows up on the game and can't be used until 'returned' by the Pokewalker. But to make it appear again, on the Pokewalker connect screen on the game itself, press and hold up, select and R. This will return the 'sent' Pokemon to your box. You do not need the Pokewalker itself, so the Pokemon is not 'lost' if the Pokewalker is lost or irreparably damaged.
I do not think that you can fix them. If the keypad isn't responding then you will have to take it to a local mobile phone shop, or your supplier.
To reset your PokeWalker status, on the screen where you have 3 choices, go for a stroll, return from a stroll, and receive a gift, press 'l' while holding 'down' and 'x'. More information is in the HG/SS instruction booklet.
wait a day without touching it does not matter in light or not that is how i fixed my ds yesterday
To fix a hardwood floor that has been damaged by water one should seek advice from a professional plumber and flooring expert. One may need to buy new flooring to replace damaged areas, or it may just need to be cleaned up.
A damaged crankshaft will need replaced.A damaged crankshaft will need replaced.
yes somtimes i would prolly say it would 99% of the time