0
How often should you use the shutdown procedure before turning off your computer?
Wiki User
∙ 12y ago
Every time you want to turn the computer off. It is bad to turn your computer off without running the standard shutdown procedures.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the problem if the compiter shut down after 2 min?
Well a couple of things usually will cause a computer to shutdown in that amount of time, first your power supply, or a temp sensor, thus a overheating cpu. To complicate matters Windows xp (before sp1) had issues with the network stack that could cause an overflow, and cause the computer to shutdown. These are the main things that may cause a computer to just shutdown, as vaug as that is. If you in need of more help, please send an email at aerowize @ yahoo dot com -Rob
Shutdown virus on command prompt?
Although not a virus, the command shutdown (Windows or *nix) will shutdown a computer.For Windows, the usage is shutdown [-i | -l | -s | -r | -a] [-f] [-m \\computername] [-t xx] [-c "comment"] [-d up:xx:yy] with the usage: -i Display GUI interface, must be the first option -l Log off (cannot be used with -m option) -s Shutdown the computer -r Shutdown and restart the computer -a Abort a system shutdown -m \\computername Remote computer to shutdown/restart/abort -t xx Set timeout for shutdown to xx seconds -c "comment" Shutdown comment (maximum of 127 characters) -f Forces running applications to close without warning -d [u] [p]:xx:yy The reason code for the shutdown u is the user code p is a planned shutdown code xx is the major reason code (positive integer less than 256) yy is the minor reason code (positive integer less than 65536)In *nix, the following applies:shutdown [-a][-t sec][-krhnfFc][time][warning-message] -a Use /etc/shutdown.allow. -t sec Tell init to wait sec seconds between sending processes the warning and the kill signal, before changing to another runlevel. -k Don't really shutdown; only send the warning messages to everybody. -r Reboot after shutdown. -h Halt after shutdown. -n Don't call init to do the shutdown but do it ourselves. The use of this option is discouraged, and its results are not always what you'd expect. -f Skip fsck on reboot. -F Force fsck on reboot. -c Cancel an already running shutdown. With this option it is of course not possible to give the time argument, but you can enter an explanatory message on the command line that will be sent to all users. time When to shutdown. warning-message Message to send to all users.
What was used to protect the computer before the anti vireses?
Before the creation of anti-virus software, there was no way to protect your computer from viruses.
What do normally clip the ground bracelet to before you work inside the computer case?
the side of the computer case
What did people use to count before the computer?
abacus (chinese)
Which procedure is recommended to ensure that the emergency locator transmitter (ELT) has not been activated?
Monitor 121.5 before engine shutdown.
How do you restart to the command prompt?
Restart your computer and a soon as Windows starts loading, press F8. There should be numerous options including one that says something like, "Safe Mode with Command Prompt." Arrow down to that option and press enter.
Why when you shutdown the computer you get a message UPnPFrameworkexe - Application Error in Windows XP?
This system is shutting down. please save all work in progress and log of. Any unsaved changes will be lost. this shutdown was initiated by NET WORLD\ netbook Time before shutdown : 0049:56 Message
How do you shutdown a computer using command prompt?
Before shutting down your system Close all open file and folders. Follow these step:- 1. Click start Button or Windows Logo Left bottom corner 2. Click Shut Down. Or you can use also shut down using CTRL ALT Delete button. or need any assistant call Techvedic expert.
Does system software start and shut down computer?
Yes it does. During the boot process the first thing the computer does is execute a small program from the 'boot block' which starts a whole series of programs to complete start-up. When you shutdown, again, another series of programs are executed to save all current settings before turning the power off.
What is the difference between shutdown option and restart option?
The shutdown option will log you off, shut down your operating system, and turn off your computer.The restart option will log you off, shut down your operating system, and then re-boot the operating system--similar to turning on your computer from a fully powered-off state.This is what will happen on a typical setup, almost all of the time.
What is the problem if the compiter shut down after 2 min?
Well a couple of things usually will cause a computer to shutdown in that amount of time, first your power supply, or a temp sensor, thus a overheating cpu. To complicate matters Windows xp (before sp1) had issues with the network stack that could cause an overflow, and cause the computer to shutdown. These are the main things that may cause a computer to just shutdown, as vaug as that is. If you in need of more help, please send an email at aerowize @ yahoo dot com -Rob
What is the difference between shut up and shut down?
Logging of your computer is just turning off your particular account so someone can go on a different account. Turning off is turning off the whole system. This way, someone would have to restart the computer before they could then log on to their own account.
How to make computer shut down automatically when not in use?
to stop a shutdown quickly you can hit the stop button before it disapers or use ctrl+alt +delete held at the same time
Why do you have to save your document to your hard drive before turning your computer off?
because then you'll lose your data.It dosen't automatically save
Shutdown virus on command prompt?
Although not a virus, the command shutdown (Windows or *nix) will shutdown a computer.For Windows, the usage is shutdown [-i | -l | -s | -r | -a] [-f] [-m \\computername] [-t xx] [-c "comment"] [-d up:xx:yy] with the usage: -i Display GUI interface, must be the first option -l Log off (cannot be used with -m option) -s Shutdown the computer -r Shutdown and restart the computer -a Abort a system shutdown -m \\computername Remote computer to shutdown/restart/abort -t xx Set timeout for shutdown to xx seconds -c "comment" Shutdown comment (maximum of 127 characters) -f Forces running applications to close without warning -d [u] [p]:xx:yy The reason code for the shutdown u is the user code p is a planned shutdown code xx is the major reason code (positive integer less than 256) yy is the minor reason code (positive integer less than 65536)In *nix, the following applies:shutdown [-a][-t sec][-krhnfFc][time][warning-message] -a Use /etc/shutdown.allow. -t sec Tell init to wait sec seconds between sending processes the warning and the kill signal, before changing to another runlevel. -k Don't really shutdown; only send the warning messages to everybody. -r Reboot after shutdown. -h Halt after shutdown. -n Don't call init to do the shutdown but do it ourselves. The use of this option is discouraged, and its results are not always what you'd expect. -f Skip fsck on reboot. -F Force fsck on reboot. -c Cancel an already running shutdown. With this option it is of course not possible to give the time argument, but you can enter an explanatory message on the command line that will be sent to all users. time When to shutdown. warning-message Message to send to all users.
If you connect a power adaptor before turning on a computer what will happen?
If the power adapter isn't plugged in before the computer is powered on, then the computer will not power on. The power supply provides power to the rest of the computer (which allows it to boot). If the power supply doesn't get power, then the rest of the computer doesn't get power. This doesn't apply to a laptop if it has a charge stored in the battery.
