0
A Transient Voltage Suppressor (Transorb) is a zener diode that is engineered for high power current switching. They function in a similar fashion to FETs but are capable of higher current and voltages than FETs. Some are "bidirectional" consisting of two zeners and allow current flow in two directions unlike a FET or Diode which allow current in one primary direction.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Working of transorb?
Transorb acts as Zener diode.It clamps the high power to certain amount of power which is usrd for the circuit
How do you test a transorb?
Testing Transorbs: Basically these are low current zener diodes. If the part is good then it will read a normal diode drop voltage in the forward bias direction and should show normal zener diode knee curve in its reverse bias direction. This value can range from a few volts to several hundred volts with the steady state current usually only a few milliamps. Note that these parts can be high voltage devices. You will need the data sheet to verify steady state operation. Running them in the steady state operation mode for any length of time isn't recommended typically. Say you are protecting a 12 volt car electronics device... the transorb would probably be rated at 15 volts threshold or a little more so that testing it for actual performance would require removing it from circuit. Transorbs can absorb a very high current spike only for a few microseconds such as a static discharge.
How can a relay circuit be used?
A relay circuit is typically a smaller switch or device which drives (opens/closes) an electric switch that is capable of much larger current amounts or a circuit which operates the coil or electronic actuator from one source and uses a separate power source to drive an isolated device. For the use in electrical engineereing:Generally speaking, using a relay may involve anything from a very robust approach to an extremely delicate approach. Consider some aspects of a relay. A relay has contacts, arcing and sparking because of back e.m.f from load circuits may damage these contacts and reduce the life span of the device. Some inductive applications might require a low value capacitor across the relay contacts. Just remember that the peak voltage (not rms or AC) of the mains running through the contacts is not more than the rated capacitor voltage value. Do not use polarized capacitors where AC is used. Often a 10nF might make a difference already depending on your back e.m.f of the load obviously. It will also reduce some EMI (electromagnetic interference)Even if your DC control signal may only see resistance of the coil at the time the coil is on or off. A coil that has inductance and store magnetic energy, the same as any coil will also produce back e.m.f when potential is removed. The collapse of the magnetic field cause a high potential difference, possibly thousands of volts at high frequency. The frequency may in fact be so high that regular diodes or transistors might not stop it. One would recommend a series resistor and use the collector of a NPN transistor with it's emitter to the ground to switch the relay on or off via the base, be sure to have a base resistor to protect the source of the control signal as well as the B-E junction of the transistor, calculation as follow:Rs = collector series resistorRb = is base series resisterbeta = current gain for the transistorVsource = the control signal voltage minimum that will turn relay on or offBy applying ohm's law we get:Rc = [Rrelay x (VCC-Vrelay -Vce)]/(Vrelay )Rb = (Vsource-Vbe)/[(Vrelay/(Relay x Beta)) x 10]{use factor 10 to compensate for error in beta values}Don't ever be to comfortable with the fact that there are no electrical connection between the contacts and the coil of a relay. Do not think relays are safe to use with computers or related micro controller devices because they are electrically isolated. It will be a bad mistake!! There are back e.m.f. from the coil aswell as e.m.i from contacts what is induced back into the coil when it has high impedance across it.It's then recommended to have a fast recovery diode in reverse bias condition across the coil to prevent back e.m.f. of finding its way back home.This is recommended to protect the driving signal source. Often in small relays using HC or TTL family logic to drive it via a transistor to a transorb or fast recovery diode across the coil may be good enough. Especially if you use it for your self and not to design a heart-lung machine for a hospital.But if you have micro controllers, computer ports. The damage of a strong back e.m.f may be more than what you bargain for and will probably happen at the worst time in the wrong place. The best is to use a opto-coupler.The control source will via a series resistor, let say about (330R for a 5V signal) switch an internal LED inside the opto-coupler device on. The light will drive a photo-transistor into forward bias condition. That can be used to drive the transistor that will energize the relay. Since there is no electrical connection between the output pin of the microcontroller that produce the control signal and the relay coil. There is only a one way communication via a light beam. This is by far safer. It creates a typical, 2500V isolation between the robust electrical circuit and it's e.m.f 's, and the sensitive and delicate micro controller or computer circuit environment. A dip in Vcc or pin for less than a millionth of a second dipping with 2 volt or spiking can cause freezing, erratic response or failure of the micro controller. For good electronic design opto-couplers are a very important part of a reliable control system that use micro controllers to control relay output with.
