0
Static is because you dont use vectors here (STA). In STA you just calculate the timings based on the signal transitation times and cell delays. Hence vectors are not applied and propagated through your circuit. Thanks, bits_dude
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Difference between the dynamic timing analysis and static timing analysis?
Dynamic timing analysis uses simulation vectors to verify that the circuit computes accurate results from a given input without any timing violations. The problem is that the simulations vector not can guarantee 100% coverage. The goal for the dynamic analysis is to get a 100% coverage. Dynamic timing simulation is still preferred for non-synchronous logic style. As a rule, however, only dynamic timing verification tools support glitch detection and race conditions, since these are inherently dynamic events. Static timing analysis on the other hand check all path in the circuit even the false paths. False paths are paths that are not possible or interesting in actual operation of the circuit. Therefore you can say that static analysis starts above 100% and works towards 100% by detecting and excluding the false paths. Static tools have made major advancements in recent years, in fact all synthesis tools use static timing analysis internally. Something good about this approach is that almost all tools using it supports multi-cycle paths, in which a path delay constraint exceeds a single clock period. Everything isn't just good, many static timing tools have problems with feedback loops. Problems with both approaches have resulted in the formation of a new tool category­hybrid timing verification. It selectively combine both static and dynamic timing in an attempt to create the best of both worlds.regards: VIPUL RAJPUT , Trident Techlabs Pvt. Ltd. Delhi
How do you read timing gun?
Pulses of light blink every time the cylinder which the timing gun is hooked up to fires. Typically, a timing gun is hooked up to cylinder #1. When that cylinder fires, a pulse of light occurs. The timing gun it to be aimed at a marking on the front of the engine, usually the harmonic balancer. By looking at the mark, you can determine how advanced (ahead) or retarded (behind) the engine is running. This is usually measured in degrees.
Explain rationalization of information flows timing and accuracy of destination of output?
https://en.wikipedia.org/wiki/Information_flow_(information_theory)
Which component controls the timing of all computer operations?
the system clock
What is the timing of Chevy 454 engine?
The timing on a Chevrolet 454 cubic inch engine is either 4 or 6 degrees before top dead center. Minor variations will produce different performance results.
What is static timing analysis in VLSI- ASIC?
Depending on the design methodologies used, three types of timing analysis methods are commonly used: 1. Manual analysis 2. Static timing analysis 3. Dynamic timing analysis
Timing on ade 407?
WHAT TIMING ARE WE TALKING ABOUT? STATIC SPILL TIMING ? CAM TIMING ? IS IT 407 TURBO OR NON TURBO ? JAY jbmdiesel@telkomsa.net 0837922103
Difference between the dynamic timing analysis and static timing analysis?
Dynamic timing analysis uses simulation vectors to verify that the circuit computes accurate results from a given input without any timing violations. The problem is that the simulations vector not can guarantee 100% coverage. The goal for the dynamic analysis is to get a 100% coverage. Dynamic timing simulation is still preferred for non-synchronous logic style. As a rule, however, only dynamic timing verification tools support glitch detection and race conditions, since these are inherently dynamic events. Static timing analysis on the other hand check all path in the circuit even the false paths. False paths are paths that are not possible or interesting in actual operation of the circuit. Therefore you can say that static analysis starts above 100% and works towards 100% by detecting and excluding the false paths. Static tools have made major advancements in recent years, in fact all synthesis tools use static timing analysis internally. Something good about this approach is that almost all tools using it supports multi-cycle paths, in which a path delay constraint exceeds a single clock period. Everything isn't just good, many static timing tools have problems with feedback loops. Problems with both approaches have resulted in the formation of a new tool category­hybrid timing verification. It selectively combine both static and dynamic timing in an attempt to create the best of both worlds.regards: VIPUL RAJPUT , Trident Techlabs Pvt. Ltd. Delhi
What is static timing?
Static Time Analysis is used for measuring "Delay Timings" between different paths, between different components in the circuit by using different timing models... The main goal of Static Time Analysis (STA) is to verify all the signals are arriving neither too early nor too late. So STA will be able to detect the problems like Glitches, clock skew, slow paths, very fast paths etc..... ................................................Amarendhar................................................................. ...................................amarendhar.ganji@Yahoo.com.................................................
What is static time analysis?
Static Time Analysis is used for measuring "Delay Timings" between different paths, between different components in the circuit by using different timing models... The main goal of Static Time Analysis (STA) is to verify all the signals are arriving neither too early nor too late. So STA will be able to detect the problems like Glitches, clock skew, slow paths, very fast paths etc..... ................................................Amarendhar................................................................. ...................................amarendhar.ganji@yahoo.com.................................................
What is the Toyota Corolla 1300 ignition timing settings?
Ignition Timing Initial/Static: 8@Idle C/S
How do you set the timing on a 1991 VW Golf?
Just to clarify the question, this is aking about static timing not dynamic with a strobe light.
Adjust timing on motorcycle?
That depends on what kind of timing you are wondering about... In a basic ignition there are two types of engine timing, static and dynamic. Static timing is the timing your engine runs at idle and low rpm. Dynamic timing is the variable (thus called dynamic) timing your engine runs on from low to full rpm. The static timing should always be set first, it depends on what ignition your motorcycle has...points? magnetic pickup? crank fired? there are several types The dynamic timing refers to the timing advance the distributor modulates through engine rpm. Setting this requires a timing light and timing marks on the harmonic balancer and engine block (usually stamped into the parts themselves from the factory). To help you out further I need to know what kind of ignition you have...a service manual will tell you what kind you have, and even how to adjust it. Best of luck!
What is variale valve timing?
variable valve timing is where the engine changes valve timing based on the driving situation much like ignition timing is changed to meet the needs of the engine in specific situations. in most cars valve timing is static and determined by the timing gear on the camshaft
What is the need of sta static timing analysis in vlsi - asic?
We need STA in VLSI - ASIC because of these reasons: # To analyze the timing relationships of a given circuit to verify that the circuit works at the specified frequency (verification). # 100 % path coverage is possible because no design specific pattern is required. # You can't achieve the clock speed without it.
How can you take a picture of static electricity?
You can't really take a photo of static electricity itself, but you could take a picture of something that is a result of static electricity.One good way to do this would be to set up two metal spheres with opposite electric charges, then bring them close together in a dark room, so that a spark jumps between them. If you could get the timing right, a nice photo might come out.You could otherwise just take a photo of static electricity in a more common situation, such as during a lightning storm or when someone takes off a jumper making their hair stand up.
How do you turn the injection pump up on a jd 4010?
To turn the injection pump up you set it to TDC static timing by rotating the pump. It is adjusted by an Allen screw on the lower side of the pump.
