answersLogoWhite

0

The wiper sets the effective resistance of the potentiometer.

User Avatar

Wiki User

10y ago

What else can I help you with?

Continue Learning about Computer Science
Related Questions

What are rotatable sliding contact of rotary potentiometer and the wiper contact of liner potentiometer represent?

it represent the resistance where it can be increased or decreased


What is linearisation of potentiometer?

Linearization of the potentiometer refers to the inclination of the three parts of a potentiometer. The parts includes a pot, is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.


Main difference between rotary and linear potentiometer?

A rotary potentiometer is designed to measure rotational movement, providing a variable resistance output based on the position of a rotating shaft. On the other hand, a linear potentiometer measures linear movement, offering a variable resistance output based on the linear position of the sliding wiper along a straight track.


What type of signal does a potentiometer produce?

A: Potentiometer does not produce any signal it is merely a variable resistor whereby any signal impressed on it can be variably taken out of the wiper as a linear function or logarithms function depending on the requirement of the design


What type of speed control system uses a wire -wound potentiometer?

A potentiometer is another name for a variable resister used for voltage dividing. Potentiometers have three tabs on them The two outer most tabs have the full resistance of the device across them. The center tab is connected to the wiper that slides across the surface of the resister. A voltage is applied to the two outside tabs on the potentiometer. A voltage of your choosing will appear across either the left tab to the center wiper tab or from the right tab and the center wiper tab. A potentiometer of this type is used to control the speed output of variable frequency drives. A 10K potentiometer has 10VDC applied across the two outside tabs If the drive sees the full 10 volts it allows the drive to go to full output and the motor will run at full speed. With the potentiometer's center tab wiper at half position a voltage of 5 VDC will appear to the drive. When the drive sees the 5 volts it tells the drive to go to half speed output and the motor will run at half speed. This potentiometer is linear so no matter where the wiper is positioned, the motor speed will follow the potentiometer settings from 1% right up to 100%


What is the principle of potentiometer?

A potentiometer is another name for a variable resister used for voltage dividing. Potentiometers have three tabs on them The two outer most tabs have the full resistance of the device across them. The center tab is connected to the wiper that slides across the surface of the resister. A voltage is applied to the two outside tabs on the potentiometer. A voltage of your choosing will appear across either the left tab to the center wiper tab or from the right tab and the center wiper tab. A potentiometer of this type is used to control the speed output of variable frequency drives. A 10K potentiometer has 10VDC applied across the two outside tabs If the drive sees the full 10 volts it allows the drive to go to full output and the motor will run at full speed. With the potentiometer's center tab wiper at half position a voltage of 5 VDC will appear to the drive. When the drive sees the 5 volts it tells the drive to go to half speed output and the motor will run at half speed. This potentiometer is linear so no matter where the wiper is positioned, the motor speed will follow the potentiometer settings from 1% right up to 100%


How the servo potentiometer works?

A potentiometer is another name for a variable resister used for voltage dividing. Potentiometers have three tabs on them The two outer most tabs have the full resistance of the device across them. The center tab is connected to the wiper that slides across the surface of the resister. A voltage is applied to the two outside tabs on the potentiometer. A voltage of your choosing will appear across either the left tab to the center wiper tab or from the right tab and the center wiper tab. A potentiometer of this type is used to control the speed output of variable frequency drives. A 10K potentiometer has 10VDC applied across the two outside tabs If the drive sees the full 10 volts it allows the drive to go to full output and the motor will run at full speed. With the potentiometer's center tab wiper at half position a voltage of 5 VDC will appear to the drive. When the drive sees the 5 volts it tells the drive to go to half speed output and the motor will run at half speed. This potentiometer is linear so no matter where the wiper is positioned, the motor speed will follow the potentiometer settings from 1% right up to 100%


An Example of a Nonlinear circuit component - resistor or diode or rheostat or potentiometer?

An example of nonlinear is the human ear! A 100 ohm linear potentiometer is one in which it's properties dictate that when it is set to it's halfway point, the impedance from the wiper (for lack of a long lost memory of the word) to one side of the pot is 50 ohms; or half of the pot's value. We hear nonlinearly. Hence, volume controls are nonlinear potentiometers. That means that when you set it to it's half way point, the impedance from the wiper to one side is greater than the that of the other side. On a graph, the 'impedance to wiper' position ratio forms a line which is not linear or not strait.


Where a varying voltage is required this can be achieved by?

Variable resistors are called rheostats. A potentiometer can be used as a rheostat. Use the wiper terminal and one of the outside terminals for connections. The third terminal of the potentiometer is unused.


A potentiometer is used for?

A potentiometer is a type of position sensor. They are used to measure displacement in any direction. Linear potentiometers linearly measure displacement and rotary potentiometers measure rotational displacement. Also known as a Potmeter or Pot, it consists of a resistive element called the track and a sliding contact called the wiper internally where end terminals are attached to the resistive element. They are used to accurately measure voltage and help achieve a variable voltage from a fixed-voltage source. Common Examples of Potentiometers are: Measuring Position on a gaming joystick Controlling audio equipment using volume controls


How can a potentiometer be a rheostat?

A rheostat and a potentiometer are two different applications for the same device, a variable resistor. These devices have three terminals. Two terminals are connected across the complete resistor, while the third terminal is connected to a controllable wiper. The variable resistance is provided between the wiper terminal and either one of the other two terminals.When used to control current, it is called a rheostat. When used to control voltage, it is called a potentiometer.


Why electric current should not be passed through the potentiometer for a long time continuously?

Passing electric current through a potentiometer for a long time continuously can cause overheating of the resistive coil and wiper, leading to damage. This can also result in changes to the resistance value and accuracy of the potentiometer, impacting its functionality. It is recommended to use the potentiometer within its specified ratings to prevent such issues.