0
a tool used to view and modify the IP configuration of a computer
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What are the functions of the following tcpip utilities nslookup winipcfg and microsoft snmp agent?
Nslookup: displays information about domain names and their ip addresses Winipcfg: A win9x/me utility to display ip address and other configuration in a user friendly window. Ipconfig: Displays the ip address of the host and other connection information Microsoft snmp agent: provides system management tools for networks
What are the ping Ipconfig and Winipcfg utilities used for?
Ping is a useful TCP/IP utility to check network connectivity. Two other useful troubleshooting tools are Ipconfig (Windows 200/XP) and Winipcfg (Windows 9x/ME), which test TCP/IP configuration.
What is WINPCFG?
I am assuming you mean WINIPCFG. This program was included with windows 98 and windows ME to allow you to identify the IP address and the MAC address of a network device installed in your computer. It also has other functions that directly relate to IP information such as renewing and releasing IP information. Windows XP and beyond include this type of thing in their networking options
How do you configure a Cisco 2950 switch?
Follow these steps to start the Express Setup program.1. Verify that no devices are connected to the switch.2. Press and hold the Mode button, as shown in Figure 1, until the four LEDs next to the Mode button turn green.This takes approximately 2 seconds.Note: This only works on switches that do not have a configuration file in their file system.3. When the four LEDs turn green, release the Mode button.Note: If all of the Mode LEDs begin to blink after you have held the Mode button for 2 seconds or you cannot get the four LEDs to remain lit, a configuration already exists on the switch. In this case the switch cannot enter Express Setup mode. See the section of this document Clearing the Switch IP Address and Configuration for the instructions on deleting a configuration file from a switch.4. Connect the Ethernet cable (not included) to a 10/100 Ethernet port on the front panel of the switch,Caution: Do not connect the switch to any device other than the PC being used to configure it.1 - Switch2 - Ethernet cable3 - PC or workstation5. Connect the other end of the cable to the Ethernet port on the PC and verify that the port status LEDs on both connected Ethernet ports are green.6.Wait approximately 30 seconds after the port LEDs turn green, and launch a web browser on your PC.7.If you are using DHCP on your PC, you need to obtain the 10.0.0.2 IP address from the switch now.Do one of the two following options depending on the operating system on your PC.If you have manually configured your PC to use 10.0.0.2, skip this step and proceed to step 8.Windows 95/98/ME:A. Select Start > Run and enter winipcfg.The WINIPCFG application opens as shown in Figure 3.Note: You must select the NIC that you have connected to the switch in the WINIPCFG window before continuing this task.If the IP address is already 10.0.0.2, proceed to step 8.B.Click Release All.C.Click Renew All.When the IP address has changed to 10.0.0.2, proceed to step 8.Windows 2000/XPa. Select Start > Run and enter CMD to open a command prompt window.b. Enter the command ipconfig /release at the prompt.c. Enter the command ipconfig /renew at the prompt.d. Enter the command ipconfig /all at the prompt to display the current settings.When the IP address has changed to 10.0.0.2, proceed to step 8.Enter the IP address 10.0.0.1, as shown in Figure 4 in the browser, and press Enter.8. Enter the IP address 10.0.0.1, as shown in Figure 4 in the browser, and press Enter.Consider the following issues if the Express Setup home page does not appear in your browser.Are you running Cisco IOS Software Release 12.1(14)EA1 or later on the switch?If not, upgrade it now.Did you release and renew the IP address on your PC using DHCP or manually configure its address to 10.0.02?If not do so now. See Appendix A: Setting up the IP address on your PC to use Express Setup for help.Did you wait 30 seconds after connecting the switch and PC or workstation before entering the IP address in your browser?If not, wait 30 seconds and re-enter 10.0.0.1 in the browser, and press Enter.Did you enter the wrong address in your web browser, or is there an error message displayed in the browser window?Re-enter 10.0.0.1 in the browser, and press Enter.Did you connect a crossover instead of a straight-through Ethernet cable between an Ethernet port of the switch and the Ethernet port of the PC, as shown Figure 3?If not, reconnect the cable to the Ethernet port on the switch and PC. Wait 30 seconds before entering 10.0.0.1 in the browser.Did you verify that POST successfully ran before starting Express Setup?If not, make sure that only the SYST and STAT LEDs are green before pressing the Mode button to begin Express Setup.Did all of the Mode LEDs begin to blink after you have held the Mode button for 2 seconds?If they did, a configuration already exists on the switch and the switch cannot go into Express Setup mode. Release the button. For more information, see the section titled Clearing the Switch IP Address and Configuration.
What displays utilities TCP IP configuration on Windows 98?
winipcfg
What command is used in Windows 98 to verify its TCP IP configuration?
winipcfg
What are the functions of the following tcpip utilities nslookup winipcfg and microsoft snmp agent?
Nslookup: displays information about domain names and their ip addresses Winipcfg: A win9x/me utility to display ip address and other configuration in a user friendly window. Ipconfig: Displays the ip address of the host and other connection information Microsoft snmp agent: provides system management tools for networks
What are the ping Ipconfig and Winipcfg utilities used for?
Ping is a useful TCP/IP utility to check network connectivity. Two other useful troubleshooting tools are Ipconfig (Windows 200/XP) and Winipcfg (Windows 9x/ME), which test TCP/IP configuration.
Which command display the IP address of the host?
It depends on the Operating System - For Win. 9x you can use winipcfg Other windows versions use ipconfig Unix and Linux use ifconfig
What are some command prompt tricks?
Any good DOS reference manual or tutorial will provide you with plenty. Some windows specific ones however: netstat -n Shows all connections to your computer winipcfg ipconfig Displays information about your local ipaddress. ping <site> Pings a website
What is WINPCFG?
I am assuming you mean WINIPCFG. This program was included with windows 98 and windows ME to allow you to identify the IP address and the MAC address of a network device installed in your computer. It also has other functions that directly relate to IP information such as renewing and releasing IP information. Windows XP and beyond include this type of thing in their networking options
Which utility enable you to reset a computer's network adapter?
IPCONFIG is one, and it is a part of Windows 2000-Win7. In the run box or the command console you would first do: Ipconfig /release Then you would do: Ipconfig /renew If you have Windows 95/98, the equivalent would be WINIPCFG, and it is in the form of a GUI, so you would click on the release or unbind button and then on the renew or bind button.
How can you refresh your IP configuration?
In Windows operating systems, open a command prompt and type "ipconfig /release," which dumps the automatic address it had, and then "ipconfig /renew," which gets a new address, which will be in the address space that you just changed the router to. Of course you won't type the quotes, and depending on which Windows version you have you may need to make it "release all" and "renew all." For Mac OS, either restart your computer, or go to the Apple menu, choose System Preferences, choose Network from the View menu, and then Active Network Ports from the View menu. Deselect the "ON" checkbox for your network adapter, click on Apply, then reselect the "ON" checkbox and click Apply again. Finally you can check your new ip address at IP-Details.com
What is Mac address of the wireless adapter?
MAC addresses are a kind of serial number. They are supposed to be unique worldwide; that is, two different network equipments, even of the same kind, will have different MAC addresses. They are used for communication, to identify the individual pieces of equipment.MAC addresses are a kind of serial number. They are supposed to be unique worldwide; that is, two different network equipments, even of the same kind, will have different MAC addresses. They are used for communication, to identify the individual pieces of equipment.MAC addresses are a kind of serial number. They are supposed to be unique worldwide; that is, two different network equipments, even of the same kind, will have different MAC addresses. They are used for communication, to identify the individual pieces of equipment.MAC addresses are a kind of serial number. They are supposed to be unique worldwide; that is, two different network equipments, even of the same kind, will have different MAC addresses. They are used for communication, to identify the individual pieces of equipment.
How do you configure a Cisco 2950 switch?
Follow these steps to start the Express Setup program.1. Verify that no devices are connected to the switch.2. Press and hold the Mode button, as shown in Figure 1, until the four LEDs next to the Mode button turn green.This takes approximately 2 seconds.Note: This only works on switches that do not have a configuration file in their file system.3. When the four LEDs turn green, release the Mode button.Note: If all of the Mode LEDs begin to blink after you have held the Mode button for 2 seconds or you cannot get the four LEDs to remain lit, a configuration already exists on the switch. In this case the switch cannot enter Express Setup mode. See the section of this document Clearing the Switch IP Address and Configuration for the instructions on deleting a configuration file from a switch.4. Connect the Ethernet cable (not included) to a 10/100 Ethernet port on the front panel of the switch,Caution: Do not connect the switch to any device other than the PC being used to configure it.1 - Switch2 - Ethernet cable3 - PC or workstation5. Connect the other end of the cable to the Ethernet port on the PC and verify that the port status LEDs on both connected Ethernet ports are green.6.Wait approximately 30 seconds after the port LEDs turn green, and launch a web browser on your PC.7.If you are using DHCP on your PC, you need to obtain the 10.0.0.2 IP address from the switch now.Do one of the two following options depending on the operating system on your PC.If you have manually configured your PC to use 10.0.0.2, skip this step and proceed to step 8.Windows 95/98/ME:A. Select Start > Run and enter winipcfg.The WINIPCFG application opens as shown in Figure 3.Note: You must select the NIC that you have connected to the switch in the WINIPCFG window before continuing this task.If the IP address is already 10.0.0.2, proceed to step 8.B.Click Release All.C.Click Renew All.When the IP address has changed to 10.0.0.2, proceed to step 8.Windows 2000/XPa. Select Start > Run and enter CMD to open a command prompt window.b. Enter the command ipconfig /release at the prompt.c. Enter the command ipconfig /renew at the prompt.d. Enter the command ipconfig /all at the prompt to display the current settings.When the IP address has changed to 10.0.0.2, proceed to step 8.Enter the IP address 10.0.0.1, as shown in Figure 4 in the browser, and press Enter.8. Enter the IP address 10.0.0.1, as shown in Figure 4 in the browser, and press Enter.Consider the following issues if the Express Setup home page does not appear in your browser.Are you running Cisco IOS Software Release 12.1(14)EA1 or later on the switch?If not, upgrade it now.Did you release and renew the IP address on your PC using DHCP or manually configure its address to 10.0.02?If not do so now. See Appendix A: Setting up the IP address on your PC to use Express Setup for help.Did you wait 30 seconds after connecting the switch and PC or workstation before entering the IP address in your browser?If not, wait 30 seconds and re-enter 10.0.0.1 in the browser, and press Enter.Did you enter the wrong address in your web browser, or is there an error message displayed in the browser window?Re-enter 10.0.0.1 in the browser, and press Enter.Did you connect a crossover instead of a straight-through Ethernet cable between an Ethernet port of the switch and the Ethernet port of the PC, as shown Figure 3?If not, reconnect the cable to the Ethernet port on the switch and PC. Wait 30 seconds before entering 10.0.0.1 in the browser.Did you verify that POST successfully ran before starting Express Setup?If not, make sure that only the SYST and STAT LEDs are green before pressing the Mode button to begin Express Setup.Did all of the Mode LEDs begin to blink after you have held the Mode button for 2 seconds?If they did, a configuration already exists on the switch and the switch cannot go into Express Setup mode. Release the button. For more information, see the section titled Clearing the Switch IP Address and Configuration.
Where is your IP address located?
To checkup your IP address: Command for Windows 2000 / XP / Vista: Go to Menu Start and select Run. Then, type the following command: cmd /k ipconfig /all Your IP address will be displayed in an open window after a few seconds. Command for Windows 95/98: Go to Menu Start and select Run. Type the following command: winipcfg Command for Linux: Type this command in a console as root: ifconfig in a console as user /sbin/ifconfig Public IP address: You can go to the following site: whatismyip
