0
What else can I help you with?
What sizes of tablet PC are available from Asus?
There are many tablets in different sizes available from ASUS. The sizes range from 7 inch, 8 inch, 9 inch to even 12 to 15 inch tablets they have for sale.
What is the difference between an lpi dpi ppi?
LPI - Lines Per Inch - Refers to the number of lines of text a printer will fit in an inch of paper. (the smaller the font size the more lines per inch) DPI - Dots Per Inch - The number of dots a printer can put within an inch of paper (the smaller the print nozzles the more DPI' PPI - Pixels Per Inch - usually relates to the resolution of a monitor.
In computers What is the unit measurement equal to 172 of an inch?
Assuming you mean 1/72 of an inch... It's called the 'point' size. Tect that is 72 point is 3/4 of an inch tall.
What does dot pitch mean?
Dot pitch is the opposite of dots per inch (or dots per mm if you're of the metric persuasion) Take a dot pitch of 0.1 inch. Since each dot is 0.1 inches across, 10 of them will fit in an inch. So, a dot pitch of 0.1 inch is the same as 10 dots per inch. For printers and monitors, the finer (smaller) the dot pitch, the better the picture.
What is the order of the types of computers from smallest to largest?
There are small to large, Netbooks (7-10 inch screen), UMPC's (11-13 in screen) , Tablet PC's (13-14 inch screen), Small Laptops (13-14 inch screen), Medium Laptops (15 inch screen), and Large Laptops (16-21 inch screens). Then there are Media Computers, normally the size of a tissue box. The average computer, and large sever towers.
What are some tools that begin with the letter Q?
Quarter inch Ratchet, Quarter inch wrench, Quarter inch socketQuarter inch socket and quarter inch wrench are tools.
WHAT Tool that start with the letter q?
Quarter inch socket and quarter inch wrench are tools. They begin with the letter q.
What socket size is required for a three quarter inch bolt?
Bolts are categorised by their thread size. The standard socket size for a bolt with a three quarter inch thread is 1 and one eighth inches. Heavy head bolts use a one and a quarter inch socket.
What size wrench for lug nuts on Ford F-250 pickup?
wrench for lug nuts on f250 is 7/8s of an inch there is a metric wrench that fits but i cant remember what size it is
What is a box wrench?
Wrenches come two ways, open ended and box end. Open end are just a U shape on the end. Box end go around the nut or bolt. If you were to slice a quarter inch off of a socket that is what the end of the wrench would look like.
What size hex wrench fits a 1996 dodge truck front brake caliper?
3/8 inch
What size is the Allen wrench for front disc brakes on a 95 Cadillac?
if it has Allen head should be quarter inch
If you have a half inch threaded bolt and trying to thread into a mm hole it almost fits but stops after a couple turns what size mm bolt do you need?
12mm is a little smaller and 13mm is a little larger than a 1/2 inch bolt.
What size hex wrench fits a 1995 dodge ram 1500 caliper?
The front caliper on a 1995 Ram is requires a 3/8 inch Allen wrench to remove the bolts.
What is the proper wrench size for an 8 300 pound raised face weldneck?
The proper wrench size for an 8-inch, 300-pound raised face weld neck flange typically requires a 12-inch or 14-inch socket or wrench, usually a 1-1/4 inch or 1-1/8 inch size, depending on the specific bolt configuration. It's essential to verify the bolt specifications, as different materials and standards may affect the required wrench size. Always consult the flange manufacturer's guidelines for the most accurate information.
What size wrench do I use for a 15mm bolt?
To fit a 15mm bolt, you should use a 15mm wrench. It's important to ensure the wrench is the correct type—either an open-end, box-end, or socket wrench—to match the specific application. If you only have imperial sizes, a 9/16 inch wrench is close but may not fit as snugly. Always double-check for the best fit to avoid rounding the bolt edges.
What size drill bit do i use for a one quarter inch bolt?
If you want the bolt to slide through the hole a 5/16 hole will work well.
