answersLogoWhite

0

A multimeter draws next to no current, so will not effectively test the power supply under load.

The voltage on the meter is averaged out and so will not show ripple current, or spurious dips in the supply.

You will need an oscilloscope to check for ripple current (poor smoothing) and the supply needs to be under a load.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

You suspect that a power supply is faulty but you use a multimeter to measure its voltage output and find it to be acceptable Why is it still possible that the power supply may be faulty?

Yes, it can be faulty. Some damaged power supplies show good output voltages on the voltage range of a multimeter but, when you connect them, they don't work properly. One possible reason is that maybe an IC in its voltage regulator has a high resistance between the common and the output. You cannot see this by shunting a voltmeter onto it. You have to place a typical load onto the output to test it.


Why the motor not start if there has a gas and electric supply?

Possible Faulty wire or even a starter or alternator failure.


Why does your 120 outlet measure 49 volts when you test it with a multimeter?

A reading of 49 volts on a 120v outlet may indicate a poor connection or damaged wiring, causing a voltage drop. It could also be a sign of a faulty ground connection or a wiring issue causing a higher voltage reading. It is important to address this issue promptly to prevent any safety hazards or damage to appliances.


When switch is off of power supply output shown on the multimeter is negative voltage from power supply?

Yes.


What is the most efficient way to determine if your power supply is bad?

test it with a multimeter


What can cause a faulty power supply?

A faulty power supply does not supply any power at all to a computer or supplies incorrect voltages. Most of the time faulty power supplies are not serviceable and require replacement.


What tool can you use to troubleshoot power supply issues measure current resistance or voltage?

multimeter


You are troubleshooting a PC that appears to be dead What are some possible causes of this condition?

A dead PC could have no power going to it. The power cable could be faulty or the circuit breaker on the power supply could be flipped. If these conditions all check out, then it is likely a faulty power supply. Try these solutions. If this doesn't work, let us know ;)


What is the best thing to do if your power supply is not functioning?

If your power supply is not functioning, the best course of action is to first check all connections and ensure that the power outlet is working. If everything appears connected correctly, consider testing the power supply with a multimeter or testing it in another computer to confirm the issue. If it's confirmed to be faulty, replace it with a compatible model. Always ensure to follow safety precautions when handling electrical components.


What is the most efficient way to determine whether your power suply is bad?

To efficiently determine if your power supply is bad, first check for visible signs of damage, such as burnt components or bulging capacitors. Next, use a multimeter to test the output voltages against the manufacturer's specifications; if they are significantly out of range, the power supply may be faulty. Additionally, try using a known good power supply to see if the system powers on correctly. If the system works with the alternative supply, it's likely that your original power supply is defective.


How do you check amp reading on a 12volt cooling fan?

To check the amp reading on a 12-volt cooling fan, you'll need a multimeter set to the ammeter function. First, disconnect the power supply to the fan and then connect the multimeter in series with the fan by placing the multimeter leads between the fan's power source and the fan itself. Once the connections are secure, reconnect the power supply and turn on the fan to read the current in amps displayed on the multimeter. Ensure safety precautions are taken to avoid short circuits or damage.


What are the steps to troubleshoot and repair a faulty dryer terminal block?

To troubleshoot and repair a faulty dryer terminal block, follow these steps: Unplug the dryer and turn off the power supply. Inspect the terminal block for any visible damage or loose connections. Use a multimeter to test the continuity of the terminal block. Replace any damaged or faulty terminal block components. Reconnect the wires securely and test the dryer to ensure it is working properly. If you are unsure about any of these steps, it is recommended to seek the help of a professional technician.