answersLogoWhite

0

RIPv1 (Routing Information Protocol version 1) sends out its entire routing table every 30 seconds. This periodic update helps ensure that all routers in the network have the most current routing information. Additionally, RIPv1 uses broadcast to send these updates to all neighboring routers.

User Avatar

AnswerBot

3w ago

What else can I help you with?

Related Questions

For ripv1 what type of routing protocol is it?

RIP v1 is a classfull distance vector protocol.It send and receive v1 informations only


Which routing protocol excludes the subnet information from routing updates?

RIP VERSIONV1 can be seen to exclude subnet information from routing updates, this is because ripv1 is a classful routing protocol and does not support VSLM, this was corrected in RIPv2 where ripv2 does send out subnet mask's in the form of a prefix eg /24 which is the subnet mask of 255.255.255.0 or a class c address.


Which 3 conditions cause some distance vector routing protocol to send routing table updates?

Distance vector routing protocols send routing table updates primarily under three conditions: when a router's routing table changes due to a new route being added or an existing route being updated, when a router receives a triggered update from a neighboring router indicating that a route has changed, and periodically at defined intervals to ensure all routers have consistent routing information. These updates help maintain accurate and up-to-date routing tables across the network.


What is the advantage of dynamic routing?

The router needs a routing table, to know where to send IP packets. The purpose of dynamic routing is to update the routing tables automatically. This means you need much less configuration, and the network dynamically adjusts to topology changes (for example, a router is added, or a cable has a bad connection).


When the destination network is not listed in the routing table of a cisco router what two possible actions the router might take?

The router discards the packet.The router forwards the packet out the interface indicated by the default route entry.


Wic address is used by the router to direct a packet between networks?

The router only needs to know the next-hop address; in other words, it sends the data to the next router; this next router then takes its own decision.Each router maintains a routing table, with information about where to send IP packets. The information is stored on a per-network basis. When the router receives an IP packet, it consults the routing table, to see what is the next-hop address, and through which interface it must send the packet.The router only needs to know the next-hop address; in other words, it sends the data to the next router; this next router then takes its own decision.Each router maintains a routing table, with information about where to send IP packets. The information is stored on a per-network basis. When the router receives an IP packet, it consults the routing table, to see what is the next-hop address, and through which interface it must send the packet.The router only needs to know the next-hop address; in other words, it sends the data to the next router; this next router then takes its own decision.Each router maintains a routing table, with information about where to send IP packets. The information is stored on a per-network basis. When the router receives an IP packet, it consults the routing table, to see what is the next-hop address, and through which interface it must send the packet.The router only needs to know the next-hop address; in other words, it sends the data to the next router; this next router then takes its own decision.Each router maintains a routing table, with information about where to send IP packets. The information is stored on a per-network basis. When the router receives an IP packet, it consults the routing table, to see what is the next-hop address, and through which interface it must send the packet.


What sends entire routing table to all routers at a schedule time?

It is typical for older routing protocols of the "distance vector" type, such as RIP, or IGRP, to send out their routing tables regularly to neighbors. By default, RIP does this every 30 seconds, while IGRP does it every 90 seconds.


Explain the effect ot the command ip classless on both classfull and classless routing protocol?

if a protocol is only classfull(RIPv1, IGRP) the command will have no effect, but in protocols that support vlsm and classless ip adressing it will enable the protocol to send the subnet mask in it's packets so that a router would not recognize only class networks, but also their subnets.


What best describes the operation of distance vector routing protocols?

They send their routing tables to directly connected neighbors.


Do you need a routing number to send money?

Yes, you typically need a routing number to send money electronically, such as through a wire transfer or direct deposit. The routing number helps ensure the money goes to the correct bank or financial institution.


Routes and their use?

If you meant "router", you may want to ask a separate question. A route is simply the path through which data travels. A router or similar equipment must keep a routing table - a table of routes, which tells it where to send data for different destinations.


Capital One wire transfer routing number?

The routing number for Capital One is 056009482 . The routing number is used to send wire transfers in the United States.