0
Is it better to have Windows volume on full and adjust the speaker volume or vise versa?
It depends on the exact sound card the computer uses. However, in general it's better to set the PC volume to a moderate level (perhaps slightly louder than you'd need), then use a volume control on the speakers to slightly attenuate the sound.
Why you may ask? Distortion, pure and simple. At maximum volume, the PC sound card is much more likely to mess up the sound (most will start doing nasty thinks like "clipping" - basically it sounds awful - and can even heat up the sound card making for more cooling work within the PC). Then that same distorted sound will be lowered to an acceptable level - but it will still be distorted.
So, turning down the PC volume will give you better sound, lower heat and power, and it's a better overall solution.
Hope this helps!
Dave (Electrical Engineer)
What else can I help you with?
How to turn up volume on speaker?
To increase the volume on a speaker, you can typically adjust the volume using the controls on the speaker itself or by using the device connected to the speaker (such as a phone or computer). Look for buttons or knobs labeled "volume" and adjust them to increase the sound output. If your speaker is connected to a device, you can also adjust the volume settings on that device to increase the sound.
How do you adjust the speaker volume on Uniden 5.8 Power Max Phone?
To adjust the speaker volume on a Uniden 5.8 Power Max Phone, locate the volume control buttons, typically found on the side of the handset. During a call, you can press the "Volume Up" or "Volume Down" buttons to adjust the speaker volume to your preference. The current volume level is usually indicated on the display. Make sure to test the volume during a call for the best results.
How can you control volume on aspiron T7384 speaker when in bluetooh mode through your iPhone?
Adjust the volume on the source device (iPhone)
The radio reception fades in and out on your Mercedes 2000 S430?
The radio adjust automatically to the amount of road noise, more noise, the radio adjust its volume, and of course, that works the same way reversed, lesser noise, lower volume needed. Test this by opening your windows while driving on the freeway, the radio adjust its volume up, so you be able to listen to the music, by closing the windows, the volume automatically turns down.
How can I plug in a microphone to a speaker?
To plug in a microphone to a speaker, you will need to connect the microphone's cable to the input jack on the speaker. Make sure the microphone is turned on and adjust the volume levels on both the microphone and the speaker to achieve the desired sound output.
Why does my radio volume go up when the windows are down?
It seems as if the Road Sound Compensation system is active It will automatically adjust the volume accordingly to cabin conditions, so if your windows are down, it notices the excess noise and then compensates for the windows being down.
How do you turn the sound back on your computer?
On WindowsXP there are two easy ways to adjust the sound, or mute it and turn it back on.First, on Windows Toolbar (bottom of screen, touch the blue arrow to expand the items. Look for the speaker icon; click it. Adjust, mute, or unmute.OR Go to Start --> Control Panel --> Sounds and Audio Devices --> Device Volume -- Adjust, mute, or unmute.
What is mean by pad?
A pad is generally a low ohm volume control used to adjust the volume of individual speakers tied to the same output of an amplifier. The main amp is set for a certain level then you go adjust the "pads' for the amount of speaker volume you want in say - each room of your house.
How can I connect a microphone to a speaker?
To connect a microphone to a speaker, you will need an audio cable with the appropriate connectors. Plug one end of the cable into the microphone and the other end into the input on the speaker. Adjust the volume levels on both the microphone and the speaker to ensure clear sound output.
How on y8.com do you turn off the volume?
To turn off the volume on y8.com, look for the speaker icon typically located in the bottom right corner of the video player. Click on the speaker icon to mute the sound. You can also adjust the volume by clicking and dragging the volume slider to the left to decrease the volume or all the way to the left to mute it completely.
How do you use the built in speaker on a hip street 2 GB HS T29 mp3 mp4 player?
In order to use the built-in speaker, you will need to enable it. Press and hold the FF button when adjusting the volume. This will enable the speaker. Press and hold the RW button when adjusting the volume and this will disable it. To enter the "adjust volume" mode, simply press the volume button while listening to music and use the FF or RW buttons for adjusting the volume and enabling the built-in speaker. The built-in speaker can work with or without the earphones plugged in. Please note that after the unit has been powered off, you will need to re-enable the built-in speaker.
What if you put an indoor speaker into a car?
It would work but you would have to adjust the power. Since you are using AC speakers DC. More power=more volume.
