What does -t mean in TCP IP ping?

What protocol is use by ping?

TCP\IP protocol is run by ping i.e Ping 132.125.12.1 -t will ping the status of device whether healthy or unhealthy The "ping" command is an ICMP (internet Control Management Protocol) control packet. Many websites disallow this type packet, so beware.

How do you ping continuously?

, the Ping command provides you with a parameter that configures the command to continuously ping the target device until you manually terminate the operation:Ping -t xxx.xxx.xxx.xxxIn this command, xxx.xxx.xxx.xxx is the IP address of the target device.To temporarily interrupt a continuous Ping operation and display the statistics, press [Ctrl][Break]. To completely terminate a Ping operation, press [Ctrl]C.

What is extended ping?

An extended ping is often used by the less technically knowledgeable to track "packet loss" or "latency". The command to run an extended number of repeated PINGs varies by platform:LINUX / UNIXping -s < ip address >Windowsping -t < ip address >Both of the above commands result in sending out 1 ping per second until the process is halted by pressing CTRL-C.

What is the use of ping command in ms-dos?

Ping command is used to check the network connectivity. You can use ping command from windows shell only, not from DOS OS as DOS does not supports networking. You can use "-t" switch with ping for continuously network checking.Syntax: Ping Example: ping 192.168.1.15 or ping 192.168.1.15 -t or ping -t 192.168.1.15

What is the command to ping a IP address indefinitely?

ping -t 10.3.9.42To ping the server at 10.3.9.42 you have to:Open Command Prompt, byFor Windows XP:Open the start menu, click on "Run..." then type cmd then press enter orclick OK.For Windows Vista:Open the start menu, and type cmd then press enter.Type ping using in this case 10.3.9.42, or for any other server type its website or its ip address, then press enter.This will send a very small file to the server (ping), and then it sends it back 4 times (pong). After this process it will show you how long it took to receive the data, how many of them timed out, the average time, and the highest and lowest time.

What is a t-ping crime?

Vandalism AND trespassing.

How do you spell ip?

IP : an acronym for "Internet Protocol", the method of connecting computers on the Internet. It involves the coding and addressing of data packets.

Two routers are connected via their serial ports in a lab environment The routers are configured with valid IP addresses but they cannot ping each other The show interface serial00 command shows t?

lmfao you really thought you where going to get the answer

What is t c p under terms in internet?

TCP = Transmission Control Protocol

I have att uverse internet. What is my ip router number?

I have at&t uverse internet. I am attempting to connect a wireless printer. I need to know my ip router number? What is my ip number for at&t uverse for wireless service.

What option is used for the windows 'ping' command to continue until stopped?

The option is "-t".Type ping /? to get a list of options. The same parameters, /?, is used for many other commands, too.The option is "-t".Type ping /? to get a list of options. The same parameters, /?, is used for many other commands, too.The option is "-t".Type ping /? to get a list of options. The same parameters, /?, is used for many other commands, too.The option is "-t".Type ping /? to get a list of options. The same parameters, /?, is used for many other commands, too.

What command is used to test network connectivity between two hosts?

PINGThe "ping" command does. It sends out an ICMP echo request message and waits for a reply. However, network administrators sometimes block the ICMP protocol. In that case, accessing a service on the remote computer (e.g. opening a Web page on a Web server) would do if the service is currently available and is not blocked.Testing connectivity between computers highly relies on networking protocols they use. Assuming it's TCP/IP (as the most widespread communication protocol used nowadays), the command to test reachability is 'ping'. To use it, you have to know IP address (which consists of 4 groups of digits separated with dots, like 10.4.199.15) or a hostname (like, remote.my.domain) of the remote computer. Launch shell interpteter and issue one the following:ping 10.5.199.15ping other.my.domaindepending on information on a remote device available to you.After issuing one of these commands, expect to see at least one of the following:ping: unknown host reemote.my.domain(in case you've mistyped a hostname)PING 10.6.199.15 (10.6.199.15) 56(84) bytes of data.^C--- 10.6.199.15 ping statistics ---2 packets transmitted, 0 received, 100% packet loss, time 7012ms(in case you've mistyped its IP address or there's some software installed blocking incoming pings)PING remote.my.domain (10.5.199.15) 56(84) bytes of data.64 bytes from remote.my.domain: icmp_seq=2 ttl=254 time=0.727 ms64 bytes from remote.my.domain: icmp_seq=2 ttl=254 time=0.727 ms64 bytes from remote.my.domain: icmp_seq=2 ttl=254 time=0.727 ms^C--- remote.my.domain ping statistics ---3 packets transmitted, 3 received, 0% packet loss, time 1003ms(in case the link between two systems is functioning properly)