answersLogoWhite

0

RAID 5

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

What is raid level?

A ______ uses block-level striping with parity data distributed across all member disks. It has achieved popularity because of its low cost of redundancy.


Which raid level uses word parity for error correction?

RAID level 3


Briefly define the seven RAID levels?

A RAID 1 creates an exact copy of a set of data on two or more disks. this is useful when read performance or reliability are more important than data storage capacity. A RAID 2 stirpes data at the bit level and uses a hamming code for error correction. A RAID 3 uses byte level striping with a dedicated parity disk. its a very rare practise. A RAID 4 uses block level striping with a dedicated parity disk. this allows each member of the set to act independently when only a single block is requested. A RAID 5 uses block level striping with parity data distributed across all memebr disks.it achieved popularity due to its low cost of redundancy. A RAID 6 extends RAID 5 by adding an adiitional parity block. A RAID 7 isn't an open industry satndard.it is based on the concepts used in RAID 3 and RAID 4 but greatly enhanced to address some of the limitations oif those levels.this increased performance of course comes at a cost..this is an expensive solution,made and supported by only one industry. boby handsome loh


Which type of RAID uses a dedicated parity disk?

RAID 3


Which method of disk writing does RAID 5 uses?

parity


What is Raid 5?

A RAID 5 uses block -level striping with parity data distributed across all member disks. RAID 5 has achieved popularity due to its low cost of redundancy. This can be seen by comparing the number of drives needed to achieve a given capacity. RAID 1 or RAID 0+1, which yield redundancy, give only s / 2 storage capacity, where s is the sum of the capacities of n drives used. In RAID 5, the yield is . As an example, four 1TB drives can be made into a 2 TB redundant array under RAID 1 or RAID 1+0, but the same four drives can be used to build a 3 TB array under RAID 5. Although RAID 5 is commonly implemented in a disk controller, some with hardware support for parity calculations (hardware RAID cards) and some using the main system processor (motherboard based RAID controllers), it can also be done at the operating system level, e.g., using Windows Dynamic Disks or with mdam in Linux. A minimum of three disks is required for a complete RAID 5 configuration. In some implementations a degraded RAID 5 disk set can be made (three disk set of which only two are online), while mdadm supports a fully-functional (non-degraded) RAID 5 setup with two disks - which function as a slow RAID-1, but can be expanded with further volumes. In the example on the right, a read request for block A1 would be serviced by disk 0. A simultaneous read request for block B1 would have to wait, but a read request for B2 could be serviced concurrently by disk 1.


What raid uses least number of hard disk?

There are three types of RAID RAID 0 (Stripping without parity) The records are distributed among all the available HDDs. The number of the HDDs may vary from one system to the other RAID 1 (Mirroring) This uses double number of HDDs. One stores the records while an equal number of HDDs forms the backup. RAID 5 (Stripping with parity) This type of raid distributes the records in n-1 disks while maintaining 1 disk as the parity disk. assuming 4 HDDs are required RAID 0 uses all the four RAID 1 uses double RAID 5 uses 4 + 1


What uses data striping to distribute data across multiple disks with no fault tolerance?

RAID 0


Which RAID level stripes data across multiple drives to improve performance?

Every RAID level stripes data across multiple drives, which improves performance compared to using a single disk. RAID 0, RAID 1, RAID 1+0, RAID 5, RAID 6, etc. all have better performance than a single disk. Other than RAID 0, all other RAID levels provide fault tolerance. RAID 1, RAID 1+0, RAID 5, RAID 6, etc. all have fault tolerance.


Which RAID level will you implement to provide redundancy?

Type your answer here...Answer Explanation: RAID 1 uses a minimum of two hard disks to mirror data for fault tolerance. Each hard disk contains a complete copy of the data. Disk duplexing improves mirroring because each disk is on a separate controller. If one disk or controller fails in a duplexing RAID 1 array, the other disk can take over immediately to provide fault tolerance.RAID 5, also known as disk stripping with parity, provides fault tolerance by striping the data across a minimum of three and a maximum of 32 disks, and by storing parity information on each disk. This allows the RAID array to recover from a single disk failure.RAID 0, also known as disk striping, is used to increase performance by striping data over a minimum of two and a maximum of 32 disks. RAID 0 provides no fault tolerance.RAID 3, also known as disk stripping with a parity disk, provides fault tolerance by writing data across three or more drives. Because the least number of hard disks is required, RAID 1 will be used instead of RAID 3.


What uses multiple disks to create one functional drive with parity spanning all the disks?

RAID 5


Why RAID 5 is more fault tolerant than RAID 0 and RAID 1?

RAID 5 is more fault tolerant than RAID 0 and RAID 1 because it uses striping with distributed parity, allowing it to withstand the failure of one drive without data loss. In contrast, RAID 0 offers no redundancy, meaning that the failure of any single drive results in total data loss, while RAID 1 provides redundancy through mirroring but requires twice the storage capacity. Therefore, RAID 5 strikes a balance between improved performance and efficient storage utilization while still providing a level of protection against drive failures.