answersLogoWhite

0

To program a UHF Pro remote to a Bell receiver 9242, first, ensure the receiver is powered on. Press and hold the "SAT" button until all mode buttons light up, then press the "Bell" button. Enter the programming code for the Bell 9242, which can typically be found in the remote's manual. Finally, press the "Enter" button to save the code, and test the remote to ensure it operates the receiver.

User Avatar

AnswerBot

1mo ago

What else can I help you with?

Related Questions

What is the code for a Westinghouse TV with a Bell Express vu remote?

What is the code to program a westinghouse TV to a bell express ve remote.


Can you use a bell receiver with dish satellite tv dish?

Bell and Bell receivers are strictly for use in Canada.


How do you make remote control stuff - 5 years old girl?

Remote control can be done many different ways.One example is how a light switch turns a light on and off.Another example is the TV remote control. It has an infrared, or invisible red, beam that is sent to an infrared receiver in the TV. When a button is pushed, the beam sends a message which the TV performs.Other possibilities include radio waves and sound waves.In fact, early TV remote controls were ultrasonic (so high pitched you can not hear it). The remote control had spring loaded hammers that struck a bell that made an ultrasonic beep. The TV has a receiver that listened for the bell, and did things as needed.These ultrasonic remote controls had no electrical part inside the remote. That is why people still call them "clickers", even though the modern infrared types do not click.


Does the 4500 bell receiver have call display?

get raped by your dad.


How do you change the remote control address on a replacement remote for a Bell Expressvu 4500 receiver?

Dish Network satellite receivers can be programmed to operate on different remote control addresses. Switching to a different address is necessary if you have 2 satellite receivers or if your neighbor's receiver is set on the same remote address and they are changing your channels. # Press the Mode button until the remote is in the SAT mode. # Press the Address button once (the SAT mode light will start flashing). # Use the numeric key to enter an address between 1 and 15 (do not put a 0 in front of single-digit addresses; 1 is the default remote address). The SAT mode light will stop flashing and stay lit. # Press the Address button again to save the change to the remote control. If you entered a valid remote address, the SAT mode light will blink 3 times. # Make sure the satellite receiver is Powered-off. If not, power the satellite receiver off and wait 15 seconds. # Press the Info button on the front of the satellite receiver. This will bring up the "Important System Information" menu. # Press the red Record button the the remote. The screen will update and the "remote address" listed on the screen will change to the new remote address of the remote control.


How do you find out the remote code on your bell remote?

To find the remote code for your Bell remote, you can check the user manual that came with your remote, as it typically includes a list of codes for various devices. Alternatively, you can visit the Bell website and search for the remote code guide specific to your model. If you don’t have access to either, you can also try using the code search feature on your remote, which automatically cycles through possible codes until it finds the right one for your device.


How do you get surround sound when hooking up netflix to a bell satellite receiver and aharman kardon1650 avr and a 46sharp aquos tv?

Check in the menu of the av receiver, it should have a setting for surround sound DTS and/or Dolby Pro-Logic. The program has to be made in surround for you to get true surround in your home.


What channel does my lg tv have to be on for bell express?

To access Bell ExpressVu channels on your LG TV, you typically need to set your TV to the correct input source that corresponds to your Bell receiver, usually HDMI. The specific channel number is not required, as the Bell satellite service operates via the receiver rather than a traditional broadcast channel. Ensure your Bell receiver is connected properly and powered on, and then switch to the corresponding HDMI input on your TV to view the channels.


Who invented the telephone receiver?

Alexander Graham Bell, same with the telephone, i believe.


Can install 2 TVs on one bell receiver?

Yes, you can install two TVs on one Bell receiver using a splitter, which allows the signal to be distributed to multiple TVs. However, keep in mind that both TVs will display the same channel since they share the same receiver output. If you want to watch different channels simultaneously, you'll need an additional receiver for each TV.


How do you hook up surround sound system and bell cable box to TV?

An HDMI cable connects from the Bell cable box to the surround receiver and then to the TV.


Is dish network in Canada?

I just wanted to clarify that Bell Canada provides the DISH Network signal from our satellites in space. Everything from the receiver to the dish is provided by Bell Canada.

Trending Questions
Where do you buy compact discs? Can you get a replacement brush for a Vidal Sassoon 1875 Ionic hair dryer? What are some of the potential dangers of indoor portable heaters? Which size dehumdifier should I get for my home? If you put a rooster in with an ex battery hen will the eggs be fertile? What is the remote code for tcl model RC198A? How can you find user manual for Hitachi washing machine model NW-7CX? What does CD 2 and 3 do for nox? Will a 1.5v a23 2123 or a 12v MN9100 Size N Format battery work instead of 4 AG13 Batteries in a laser pointer? SHARP ES-S52E washing machine sometime it is not working properly the problem is that user manual book which you have is in japan language if anybody have the English manual please send you? How do you get a Klaus working have a new battery the second hand goes around but hands do not move? What is the capacity of whirlpool washer LXR9245EQ1? Can you get toothpaste in the center of a CD? Can an alternator stop a car from running even with a good battery? How do you find the charging amp specs for uniden bearcat bc560xlt? Universal remote with no name on it how do you figure out the codes? If you use a AC to DC adapter with a higher current rating on a piece of electronic gear with a lower current rating can you damage the gear? What is the universal remote code for a sunkey converter box? In one year an appliance company sold 231 washing machines 302 dryers 467 stoves 532 dishwashers and 1283 microwave ovens How many appliances were sold altogether that year? How much does a sharp tv model 27f631 weigh?