answersLogoWhite

0

Manual says to hold down left and right brightness buttons for 10 seconds.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How do you reset a speed stacking timer?

you push the reset button


How do you one hundred percent complete Klonoa of the Wind Door to Phantomile on the Wii?

Fully Responding to Discussion Section:Each vision has a maximum "diamond" count of 150. The diamonds are specifically known as dream stones. Some levels are capable of exceeding 150 dream stones but that is if the player manages to manipulate some dream stone accumulation (usually using a mirror fairy that gives x2 per stone temporarily). Once the player accumulates 150 dream stones within that vision, the green dream stone icon on the world map for that vision will turn blue.The gold medallion is obtained in Reverse Mode. *spoiler* Once in reverse mode, there will be a white swirling portal located somewhere on each vision. Once in the portal a timer will start (just like on the Ex Vision) and the objective is to reach the end of the new location as fast as possible. The medallion is at the end and so is the return portal. It is possible to jump back into the portal you entered from to reset the timer.


How do you reset a kingshield T21B-H immersion heater timer?

Ah, resetting a Kingshield T21B-H immersion heater timer is as simple as painting happy little trees. First, locate the reset button on the timer unit. Press and hold the reset button for a few seconds until the display resets. Just like that, you've reset the timer and can now enjoy a warm and cozy home. Happy resetting!


How long does it take for a timer ball to max out?

A timer ball cant max out, however once you use a timer ball the number of turns that have took place will be reset


How do you reset a central timer module?

Unhook the battery for ten minutes.


How do you reset timer in visual basic 6?

' Disable the timer tmrMyTimer.Enabled = False ' in milliseconds, you can remove this line if you do not want to change the ' internval from the original setting tmrMyTimer.Interval = NewInterval ' Enable the timer again tmrMyTimer.Enabled = True


How do you reset the maintenance required light on a 1991 Jeep Cherokee Laredo?

Unplug or replace maint. timer


How do you operate montgomery ward sauna model 74-93025?

Set the timer then the heat


How do you reset a Columbia wrist watch?

TIME mode: Press and Hold "Reset" CHRONO mode: Press "ST/SP" and then press and hold "Reset" TIMER mode: [Sorry, I don't know] ALARM mode: [Sorry, I don't know]


How do you get 13 minutes from a 7 minute and a 5 minute eggtimer?

you flip both timers (with all of the sand on one side) and once the five minute timer runs out the first time, you flip the five minute timer. Once the nine minute timer runs out, you flip the five minute timer again. After the five minute timer has run out, it will have been 13 minutes. (5+4+4=13)


How do you wire on delay timer?

The timer will have terminals associated with it. They may be on a relay socket that the relay plugs into. There will be two terminals used to bring the supply voltage to the relay timer. The load will be connected in series to either an open or closed set of contacts on the relay. The load voltage is controlled by the timer relay.The operation is, when the timer relay coil is energized the timing circuit in the relay is energized. This starts counting down until the time set point is reached and then the contacts either open or close depending on what set of contacts that you connected the load to.Some timer relays need to have the timer coil circuit de energized to reset the timing relay, others use a separate input voltage terminal on the relay to reset it without having to de energize the whole relay.


How can I troubleshoot and fix issues with my defiant light timer?

To troubleshoot and fix issues with your defiant light timer, first check the power source and ensure it is properly connected. Next, reset the timer by unplugging it for a few minutes and then plugging it back in. If the issue persists, refer to the user manual for specific troubleshooting steps or contact the manufacturer for assistance.