0
The reason why the flames on your gas fireplace do not turn up could be because the gas valve is not turned up high enough. Another problem could be that the holes on the main burner are clogged up, in which case you can clean them with a stiff brush once you have turned off the gas at the mains supply.
What else can I help you with?
How do you use the word flames in a sentence?
The factory just went up in flames. The flames in the barbecue pit are too high.
Why does gas fireplace pilot light but switch for logs doesn't cause logs to come on?
See if the holes in the metal grid are blocked so that the flames can not come up.
How do you convert a wood burning fireplace into a gas fireplace?
first off you need to turn off the gas then, cap the gas line then remove the gas line and the vent pipes up in the chimney, then remove the insert or gas log, then install damper doors, put on a suitable door to the fireplace, and put a basket in the fireplace to hold the wood The above paragraph assumes that the fireplace was originally a wood burning fireplace that was retrofit to accommodate a gas fireplace insert and in that circumstance the information is accurate. However, if the fireplace was originally designed as a gas appliance it cannot be converted to solid fuel ( wood ).
Can a gas log fireplace be changed over to wood fireplace?
First off you need to turn off the gas and cap the gas line. Next, remove the gas line and the vent pipes up in the chimney. After that, remove the insert or gas log and install damper doors. Then, put on a suitable door to the fireplace. Finally, put a basket in the fireplace to hold the wood.http://wiki.answers.com/How_do_you_convert_a_gas_fireplace_into_a_wood_burning_fireplace#ixzz17W5OFp8M
Why does your fireplace mantel get hot when the gas is lit?
When the gas is lit in a fireplace, the flames generate heat that radiates outwards. Some of this heat warms the materials around the fireplace, including the mantel, causing it to become hot. The mantel is designed to withstand a certain amount of heat, but it is important to ensure it is not excessively hot to prevent any safety hazards.
How do you turn on the fireplace on club penguin?
While you are editing your igloo click and drag the fireplace and before you set it down press up. you can make it light up and make the fireplace a different color by pressing down.
How do you connect gas fireplace?
First off, you need experience in pipe-fitting. If you don't, call a plumbing company that does.The tasks you will need to perform are:Shutting of the main gas supply and all appliances that use natural gasEnsuring the atmosphere is free of natural gasPOINT A: Plotting out the route from a point on the interior gas lines (at which you can cut, thread and fit a junction) to your fireplace. NOTE: if there is no gas fitting and fireplace feeder at the fireplace, I am not writing how to do that - See your fireplace manufacturer or literaturePOINT B: Running the pipe under the floor and through the floor joists to the connection point under the fireplaceCutting, threading and fitting the feed line from POINT A at POINT BTesting Your Work So You Do Not Blow up Your HouseIf you a DIYer, you may not be able to detect any gas leaks in your finished connectionCall your gas company or a certified plumbing contractorYou will need to ensure there are no leaks after you turn the gas supply back on and prior to turning appliance on that can ignite natural gas (or allowing any sparks of flames anywhere in your house.Short version: Call a pro
How can I safely relight the pilot light on my gas fireplace?
To safely relight the pilot light on your gas fireplace, follow these steps: Turn off the gas supply to the fireplace and wait for at least 5 minutes for any lingering gas to dissipate. Locate the pilot light assembly and follow the manufacturer's instructions on how to access it. Use a long lighter or match to ignite the pilot light while holding down the pilot button. Once the pilot light is lit, continue to hold down the pilot button for about 30 seconds to allow the thermocouple to heat up. Release the pilot button and check to ensure the pilot light stays lit. If it goes out, repeat the process. Turn on the gas supply and test the fireplace to ensure it is working properly.
Can you convert a wood burning fireplace to a vent-less?
remove burnt coal, replace with seasoned firewood The above will not work! If you've ever seen a coal fireplace you would realize it is MUCH smaller than a wood burning fireplace. It would require major changes, probably not possible. A normal fireplace will burn either coal or wood or a mixture of both. If the size of the logs is controlled then their is no need to adapt the hearth.
How can you compute the natural gas consumption of your fireplace?
Turn off all of the gas appliances in the home except for the the fireplace. Watch the gas meter for 60 seconds and record the cubic foot usage, multiply the reading you get times 60 and that is your NG consumption for 1 hour. To convert to btu, multiply the 1 hour reading by 1000 and that #, if the fireplace is set up and burning properly should be the same as the Input rating on the fireplace tag. If you simply want to know how much gas you are using when lit, divide the Input rating on the tag by 1000 and that will tell how much NG you are using per hour in cubic feet.
How do you clean melted fabric off a gas fireplace front?
When fabric melts off a gas or fireplace front, it can be cleaned using a damp cloth or some abrasive material. The chirred surfaces will loosen up and wash off.
Why is my gas fireplace making noise even when it is turned off?
A gas fireplace may make noise when turned off due to the cooling process of the metal components, such as the expansion and contraction of the materials as they heat up and cool down. This can cause clicking or popping sounds as the fireplace cools down after use.
