0
What else can I help you with?
Does the stereo on a 2003 Cavalier have connections for a amplifier and sub-woofer?
it will not have r.c.a outputs but you can wire up a high to low speaker convertor which will give you the r.c.a outputs you require
What type of wire do you use to connect a computer to a television?
Depends on the inputs on the TV and outputs on the computer. You can use Firewire, USB, or component.
What do you need for subwoofers?
well you need a box first off. then you need an amp. and then an aftermarket CD player with sub outputs in the back. then you need speaker wire, and and amp installation kit (or long power wire, like 5 feet max of ground wire, and remote wire (which is just ordinary primary wire), and you will also need to buy long rca cord with male ends on both siddes
What is the standard wire color for PLC inputs and outputs?
There is no specific standard for PLC inputs or outputs, as existing standards wire color codes are based on voltage rather than by function. Different standards apply in the USA, Europe or other countries, and it depends if you intend to wire a PLC for a domestic application or it is going to another place where the requirements may be different to the local ones. Check it. These standards my help you: NFPA 79 UL 508A IEC 204.1 / EN 60204-1 If you mention where you are located or where is that piece of equipment going, maybe I can give you further info.
Can you Connect an amplifier to your factory head unit in a BA falcon?
Yes you can. You need to buy an inline convertor that takes the speaker output from the back of the head unit and turns them into RCA outputs. Then you need to find any wire that powers up when the car is on and off when the car is off. Splice into that wire from the Remote turn on wire. The rest is a simple.
I have an old bell and howell receiver with ONLY one left and one right rca speaker outputs how do you connect regular speakers to them that use standard speaker wire?
Replace the speaker wire with ones that have RCA type male plugs on one end and loose ends on the other. The loose ends are sometimes called PIG TAILS.
Which kind of wires will I need to hook up my Amp?
You'll need RCA style cables to connect from your headunit to the amp. You'll then need Speaker Wire to run from the outputs of the Amp to the speaker terminals. You'll also need a heavy gauge power wire. A wiring kit such as the StreetWires Power Station PSK04Ri 4-gauge amplifier wiring kit.
A wiring diagram for a Sony cdx-gt65uiw?
A wiring diagram for the Sony CDX-GT65UIW typically includes connections for power, ground, speaker outputs, and antenna. The power wires usually consist of a red wire for ignition (12V) and a yellow wire for battery (constant 12V). Speaker outputs are color-coded, with common colors being gray and gray/black for the front right, white and white/black for the front left, and so on for rear speakers. For accurate installation, always refer to the specific wiring diagram provided in the user manual or on Sony's official website.
Where do you hook up your remote wire from amp to stock stereo for a 2006 Chevy Malibu?
You can buy an adapter that hooks up to the speaker outputs and generates a true turn on lead or you can hook it up to ignition (pink) at the key switch if you want to save money.
You swallowed a wire from your braces?
if you think or know that you have swallowed a wire, just follow these simple steps: 1. if you are unsure wither you have swallowed it or not, just carefully check the insides of your mouth. 2. if you are experiencing pain in the throat, excessive coughing or difficulty breathing, the bracket wire may have become lodged in your airway, and you should immediately contact your orthodontist or a nearby emergency care facility. if a person you trust is able to see the wire, they may carefully remove it if its possible, but shouldnt if they believe it will cause harm. \ tell the patient to calm down and call an emergency hotline or the closest hospital.
What do you mean by sourcing and sinking?
A sourcing output supplies current or voltage to the load. The output would be hooked to one side of the load, and the other side is grounded. A sinking output works by pulling the voltage or current to ground. In this case, the load is connected to the 'hot' power supply terminal, and the other end is connected to the sinking output. When the output goes active ("goes low"), current flows from the power supply, through the load, then to ground via the output terminal. Sinking outputs are sometimes called 'open collector' outputs. You can visualize it this way: Take a light bulb and hook one lead to the chassis of your car. You just grounded the load. Now take a wire and hook it to the positive battery terminal. When you touch the battery wire to the bulb, it lights. You are 'sourcing' current to the bulb. Now, connect the bulb to the positive battery terminal. Take a wire and connect it to the car's frame (ground). The bulb already has a voltage supply - the positive battery terminal. When you touch the ground wire to the bulb, sinking current to ground, the bulb lights. The big deal here is IC's that sink current typically have much greater current capability than those with sourcing outputs. So why even bother with sourcing outputs? Their main claim to fame is the load can be ground-referenced, which is very desirable in some situations.
Replacing air thermostat for central air conditioner?
1st thing to do is turn off power to unit. if you dont do this you risk of burning up the transformer.. all thermostat wires are color coded. if you can pull the old thermostat off and match them to the new thermostat it shouldnt be a problem hopefully the tecnician who installed the unit hooked it up right but the color code should be this- R is RED that is your power wire 24v Y is YELLOW that is your cooling wire W is WHITE that is for your heat G is GREEN that is your operating the fan Those 4 are for straight heat and cool.. if you have a heat pump there will be an aditional wires which is- O is ORANGE wire that is for the reversing vavle some units also have a common wire and that is the BLUE wire.. That would be attached to the C terminal on a stat..
