answersLogoWhite

0

Reference: the density of 25% NH4OH solution = 0.907g/cm³

Therefore 1 litre of solution has mass 907g

25% = 25/100*907 = 226.75g NH3 in 1 litre solution

Molar mass NH3 = 17.031 g/mol

226.75g = 226.75/17.031 = 13.31N solution

To make 1 litre of 2N solution: ( Work in ml= 1000ml)

N1V1 = N2V2

13.31*V1 = 2*1000

V1 = 2000/13.31

V1 = 150.2ml

Measure out 150.2ml of the 25% solution and dilute to 1 litre. This is a 2N solution.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Earth Science

How do you prepare 6n ammonium hydroxide from 30 percent solution?

To prepare 6 nM ammonium hydroxide a 30 percent solution you need to know the volume of the 30 percent solution that you have and the volume of 6nM solution you would like to make. Then use the following formula: C1V1 = C2V2 where C = concentration in moles/Liter and V = volume in liters.


How prepare 6N ammonium hydroxide?

To prepare a 6N solution of ammonium hydroxide, you would first need to calculate the molarity of the concentrated ammonium hydroxide solution you have on hand. Typically, concentrated ammonium hydroxide solutions are around 28-30% NH3 by weight. To make a 6N solution, you would dilute the concentrated solution with the appropriate amount of water to achieve a final concentration of 6N. It is crucial to handle concentrated ammonium hydroxide with care as it is a corrosive substance and can cause burns upon contact with skin or eyes.


What is the Method of preparation of 3 percent solution of sodium hydroxide?

To prepare a 3% solution of sodium hydroxide, you can dissolve 3 grams of sodium hydroxide pellets in 100 mL of distilled water. Ensure proper safety precautions are taken when handling sodium hydroxide as it is a caustic substance that can cause burns.


How do you prepare 100mM ammonium acetate?

To prepare the buffer using solid form reagents, prepare a 0.1 M ammonium acetate solution by dissolving 7.7 g ammonium acetate in a 1000 ml water. Adjust 1 L of this solution to pH 4.5 by adding acetic acid (about 8 ml) and 5 ml of 1 M p-TSA (equivalent to 5 mM p-TSA).


How do make 0.1N ferrous ammonium sulfate solution?

To make a 0.1N solution of ferrous ammonium sulfate, you first need to calculate the molecular weight of the compound. Then, you can dissolve the calculated amount of ferrous ammonium sulfate in the appropriate volume of water to prepare the desired concentration. Finally, make adjustments to the pH if needed.

Related Questions

How do you prepare 6n ammonium hydroxide from 30 percent solution?

To prepare 6 nM ammonium hydroxide a 30 percent solution you need to know the volume of the 30 percent solution that you have and the volume of 6nM solution you would like to make. Then use the following formula: C1V1 = C2V2 where C = concentration in moles/Liter and V = volume in liters.


How do you prepare one liter of a 1.25M ammonium hydroxide solution?

To prepare 1 liter of a 1.25M ammonium hydroxide solution, you would need to dissolve 42.14 g of ammonium hydroxide (NH4OH) in enough water to make a total volume of 1 liter. Measure out the correct mass of ammonium hydroxide, add it to a volumetric flask, and then add water while stirring until the final volume reaches 1 liter. Make sure to wear appropriate safety gear and handle ammonium hydroxide with caution due to its caustic properties.


How prepare 6N ammonium hydroxide?

To prepare a 6N solution of ammonium hydroxide, you would first need to calculate the molarity of the concentrated ammonium hydroxide solution you have on hand. Typically, concentrated ammonium hydroxide solutions are around 28-30% NH3 by weight. To make a 6N solution, you would dilute the concentrated solution with the appropriate amount of water to achieve a final concentration of 6N. It is crucial to handle concentrated ammonium hydroxide with care as it is a corrosive substance and can cause burns upon contact with skin or eyes.


HOW TO PREPARE 13.5N AMMONIUM HYDROXIDE SOLUTION?

To prepare a 13.5N ammonium hydroxide solution, you would need to dilute concentrated ammonium hydroxide solution (typically 28-30% concentration) with water in the proper ratio to achieve the desired concentration. Calculate the volume of concentrated ammonium hydroxide and water needed based on the desired final volume of the solution and mixing the two components slowly to avoid splashing. Ensure to wear appropriate personal protective equipment and work in a well-ventilated area when handling these chemicals.


How to prepare ammonium in the school laboratory?

To prepare ammonium hydroxide in a school laboratory, mix ammonia gas with water in a suitable container. Ammonia gas can be generated by adding a strong base, such as sodium hydroxide, to ammonium chloride solution. The resulting solution will contain ammonium hydroxide, which can be used for various experiments. Always ensure proper safety measures and follow laboratory protocols when handling these chemicals.


How do you make buffer solution of ammonium chloride and ammonium hydroxide of pH 10?

To prepare a buffer solution of pH 10 using ammonium chloride and ammonium hydroxide, you would mix the two solutions in a specific ratio determined by their pKa values. The concentrations of ammonium chloride and ammonium hydroxide should be carefully calculated to achieve the desired pH. It is important to use a pH meter to verify the pH of the buffer solution and make adjustments if necessary.


How do you prepare 6 percent Ammonium Acetate?

To prepare a 6% solution of Ammonium Acetate, weigh out 6 grams of Ammonium Acetate and dissolve it in 100 mL of water. Stir the mixture until the Ammonium Acetate is fully dissolved. This will give you a 6% Ammonium Acetate solution.


How can a solution of ammonia be used to prepare ammonia sulphate?

A solution of ammonia can be used to prepare ammoniumsulfate by reacting it with a solution of sulfuric acid to produce a solution of ammonium sulfate, which can be dried if desired to prepare solid ammonium sulfate.


How to prepare ammonium hydroxide solution?

You will mix NH4OH with water. To get a specific concentration you will need to calculate the number of moles required and covert this to a mass. Use the molar mass of NH4OH. eg. 100 mL of 0.5 mol/L NH4OH -> 35.06 g/mol x 0.5 mol/L x0.100 L Notice the units cancel to g. Obtain this amount using a balance and add water to 100mL.


How would you prepare a sample of pure dry ammonium nitrate?

To prepare a sample of pure dry ammonium nitrate, dissolve ammonium nitrate in water to form a saturated solution, then allow the solution to cool and crystallize. Filter and dry the resulting crystals to obtain pure dry ammonium nitrate.


How do you prepare a 0.4 molar solution of sodium hydroxide from 96 percent sodium hydroxide pellets?

16.5g 97% pure NaOH pellets dissoved in 1 litre of distilled


How do you prepare ammonium chloride?

Mix ammonia with a solution of hydrochloric acid, then evaporate the solution. The remaining salt is what you want.