Pot holes are cracks or weaknesses in roads. If there is a crack/crevice in the road then water may enter and freeze over night, expanding the crevice. As this process repeats and the road is used more then the pot hole will expand in size.
DO NOT ATTEMPT ALONE! YOU'LL NEED AN ADULT TO ASSIST YOU IN THIS PROJECT!Child's pinwheelAluminum foilEmpty soup can or similar sized tin can with one end cut offA wooden rulerSmall cooking potHot plateHammer10p nailTape or rubber bandsMitten type of pot holderTake hammer and nail and carefully punch a hole in the end of the tin can near the edge. Punch another whole directly across the top from it. The two holes should not be bigger than 1/8 inch across.Tape or attach the ruler to can with rubber bands.Put water into the pot and cover the top of the pot with two layers of tin foil. Tightly crimp the tin foil around the edges so it seals the top tightly.Using the nail, punch a hole in the top of the tin foil cover in the very center about 1/16 inch across. Put covered pot to side.Put the pot onto the hot plate and bring to a boil.Put on the mitten pot holder, and when steam starts coming out of the top, carefully hold the pinwheel over the one hole. Notice how fast the wheel spins.Take the can on the ruler and place it on the top of the pot so that the hole is in the center of the open end of the can. Steam should now be coming out of the top of the can through the two holes.Carefully hold the pinwheel. Turn the pinwheel so that the holes are on opposite sides of the pinwheel. Notice how fast the pinwheel turns.Take pot off the hot plate and let cool. Carefully take off the tin foil, add more water to the pot and put tin foil top back on. Take the nail and poke lots of holes all over the tin foil. Punch 5 holes close to the edge away from the center hole, repeat the experiment with ten holes around the edge, 20 holes around the edge.Bring the pot back up to boiling. Hold the pinwheel over only the one center hole. How much steam do you see? How fast is the pinwheel turning?With one hole the pinwheel, how fast did the pinwheel turn? With the can making the steam hit the wheel equally on either side, what happened? When you punched more holes in the tin foil what happened?In a geothermal power plant, steam is used to turn a turbine. The turbine is attached to a generator to make electricity. There are two places in the world where natural steam is found under ground and is used to make electricity. One is in Italy. The other is north of San Francisco in an area called The Geysers. The Geysers produces enough energy to power a city of about one million people. But in recent years, the amount of steam produced by the area has decreased. Some people think that it's because there are too many "holes" in the ground like the pot cover with 20 holes. It's like having a soda with 20 straws in it and all of your friends and you sipping at the same time. The soda glass will be drained VERY fast. That's what some people think is happening to the Geysers…that it's running out of steam.
Hydrogen and chlorine can be separated by passing them through a porous pot because hydrogen molecules are smaller and can diffuse faster through the pores of the pot compared to chlorine molecules. As a result, hydrogen will pass through the pot more rapidly, allowing for the separation of the two gases.
The movement of air mass over Earth's surface causes changes in weather patterns, including the formation of high and low pressure systems, wind patterns, and precipitation. These movements can lead to the development of storms, such as hurricanes, tornadoes, and thunderstorms.
Radiation and conduction have nothing to do with it. Convection causes the water at the bottom of the pot to heat up, lowering its density and sending it to the top of the pot. It then cools, increasing its density and sending to the bottom of the pot. Repeat.
The water in an earthen pot stays cool due to a process called evaporative cooling. When the water evaporates from the porous surface of the pot, it releases latent heat, which lowers the temperature of the water inside. This natural cooling effect helps to keep the water cool even in hot weather.
Mainly caused from excessive stress on the suspension ie. pot holes, bumps, etc.
pot holes, broken parts, wear and tear, kids messing around in the snow an slamming into a curb, you name it
To properly pot a ponytail palm plant, use a well-draining potting mix, ensure the pot has drainage holes, place the plant in a sunny location, water sparingly, and avoid overwatering. This will help promote healthy growth and development of the plant.
Probably because the small ones remind them of the holes woodchucks make.
To properly plant aloe vera in a pot for healthy growth, use well-draining soil, choose a pot with drainage holes, place the aloe vera in bright indirect sunlight, water sparingly, and avoid overwatering.
A "pot hole" sinks in like a pot... The sky has a hole in it per say... It's called the hole in the ozone layer...
To safely drill holes in a terracotta pot, you can use a masonry drill bit and a power drill. Make sure to wear safety goggles and gloves to protect yourself from flying debris. Start by marking the spots where you want to drill the holes, then slowly drill through the terracotta pot using a steady hand and light pressure. It's important to go slowly to prevent cracking or breaking the pot. Once the holes are drilled, you can use them for drainage or to hang the pot.
There are alot of them but im not sure of the count!
deep pot holes
To properly plant a plant in a pot for healthy growth, choose a pot with drainage holes, use high-quality potting soil, plant the plant at the same depth as it was in its original container, water it regularly but avoid overwatering, and place it in a location with appropriate sunlight for the plant's specific needs.
To effectively drill drainage holes in plastic pots, use a drill with a sharp bit that is suitable for plastic. Mark the spots where you want to drill the holes, then slowly and steadily drill through the bottom of the pot. Make sure to clean out any plastic debris from the holes before using the pot for planting.
It is not uncommon to have a hub wear out early on any chevy,ford, or dodge however off roading hitting curbs, pot holes, ect do not help