0
Water will be in a the gaseous form of steam at 150 degrees centigrade. Water begins to boil at 100 degrees centigrade at sea level.
What else can I help you with?
What phase is water in at 1 ATM pressure and 150 and degC?
Water is in the liquid phase at 1 ATM pressure and 150 degrees Celsius. At this temperature and pressure, water exists as a liquid.
If a vessel under 2.015 ATM pressure conains N2 na d water vapor What is the partial pressure of the water vapor if partial pressure of N2 is 1.908?
To find the partial pressure of water vapor in the vessel, subtract the partial pressure of N2 from the total pressure: Partial pressure of water vapor = Total pressure - Partial pressure of N2 = 2.015 ATM - 1.908 ATM = 0.107 ATM.
As oxygen heated will solid Oxygen sublime or melt under a pressure of 1 ATM?
Under a pressure of 1 atm, solid oxygen will sublime when heated. This is because the triple point of oxygen is at a pressure lower than 1 atm, so heating solid oxygen at 1 atm will cause it to bypass the liquid phase and transition directly to a gas.
Suppose two gases in a container have a total pressure of 1.20atm what is the pressure of gas B if the partial pressure of gas A is 0.75atm?
The pressure of gas B can be calculated by subtracting the partial pressure of gas A from the total pressure. Therefore, the pressure of gas B would be 1.20 atm - 0.75 atm = 0.45 atm.
What Is tellurium normal phase?
The normal phase of tellurium, which is a metal, is solid.
What phase is water in at 1 ATM pressure and 150 and degC?
Water is in the liquid phase at 1 ATM pressure and 150 degrees Celsius. At this temperature and pressure, water exists as a liquid.
What phase is water in at 1 ATM pressure and 150oc?
Gaseous. If that is 150 degrees C, that would be steam.
What phase is water in at 75 C and 9atm?
Water is in the liquid phase at 75°C and 9 atm pressure. At this temperature and pressure, water exists as a liquid due to the combination of temperature and pressure conditions present.
Consider the phase diagram below What phase change occurs as the pressure on the sample at -50ºC is increased from 1 atm to 3 atm?
At -50°C and 1 atm, the substance is in the solid phase. With an increase in pressure to 3 atm, the phase transition will occur from the solid phase to the liquid phase.
According to the phase diagram for H2O what happens to the phases of water at 0 degC as the pressure is increased from 0 ATM to 10 ATM?
water changes from a gas to a solid to a liquid
Using the phase diagram for H2O, which of the following correctly describes water at 0°C and 1 atm?
At the melting point (Explanation) if you look at the phase diagram and look at the point where the water is 0 degrees C and 1 atm, they meet right on the line. This is the line that shows the melting point of this substance. Therefore, since the point is on the line, water at 0 degrees C and 1 atm is at the melting point.
What happens to water at 100 Celsius as pressure is increased from 0.8 ATM to 1.2 ATM?
As pressure is increased from 0.8 ATM to 1.2 ATM at 100 degrees Celsius, the boiling point of water also increases due to the higher pressure. This means that the water will remain in liquid form rather than boiling into steam until the new, higher boiling point is reached.
How does the melting point of water change as pressure increases from1atm?
The melting point of water decreases as pressure increases from 1 atm. At pressures above 1 atm, water requires a lower temperature to melt because the increased pressure helps to stabilize the solid phase.
According to the phase diagram for H2O, what happen to the phase of water at 0.5 atm pressure as the temperature is decreased from 110 C to -10 C?
Water changes from gas to liquid to a solid
What happens to water at 100C as pressure is increased from pressure 0.8 (ATM) to 1.2 pressure (ATM)?
As pressure increases from 0.8 ATM to 1.2 ATM, the boiling point of water also increases. Therefore, at 100°C and 0.8 ATM, water would boil, but at 1.2 ATM, the water would need to be heated to a higher temperature to reach the new boiling point under the increased pressure.
What is the pressure in ATM at the normal boiling point of water?
At the standard atmospheric pressure of 101325 Pa water boils exact at 100 degrees Celsius.
If a vessel under 2.015 ATM pressure conains N2 na d water vapor What is the partial pressure of the water vapor if partial pressure of N2 is 1.908?
To find the partial pressure of water vapor in the vessel, subtract the partial pressure of N2 from the total pressure: Partial pressure of water vapor = Total pressure - Partial pressure of N2 = 2.015 ATM - 1.908 ATM = 0.107 ATM.
