0
What else can I help you with?
What is Briggs and stratton battery voltage?
Generally 12 VDC. 24 VDC set-ups are out there, but rare. Keep in mind, though, it is very likely that the equipment manufacturer, NOT Briggs, will supply the battery, and any specs will come from them. (e.g. on a Toro mower w/ a Briggs engine, Toro supplies the battery).
What are the differences between the parts of a generator and the parts of a motor?
In principle a generator is the same as a motor. In a dc motor the voltage generated by the rotating armature is slightly less than the supply voltage which causes power to flow in from the supply. If an engine is then coupled to the shaft causing it to rotate faster, then it generates more voltage and power flows back into the supply. That is how a motor becomes a generator.
What is meant by load in diesel generators?
Any device that uses the generator to supply its operating voltage is electrically classed as a generator load.
Why do the lights flicker on your 240v generator?
Flickering lights on a 240V generator can be caused by several factors, including an unstable power supply, loose connections, or fluctuations in the generator's output voltage. It may also indicate that the generator is overloaded or that the fuel supply is inconsistent. Additionally, issues with the generator's internal components, such as the voltage regulator or alternator, could contribute to the flickering. Regular maintenance and checks can help identify and resolve these problems.
What is the correct spark plug gap for a toro lawnmower 190cc 7.0 hp?
It is probably a Briggs & Stratton engine. You will need to supply the model number from the engine to get a correct gap.
How many amps does a 8000 watt generator supply?
In order to determine the amperage supplied by an 8000 watt generator, you need to know the voltage of the generator. You can calculate the amperage by dividing the wattage by the voltage. For example, if the generator operates at 120 volts, the amperage would be 8000 watts / 120 volts = 66.67 amps.
Where can a DC exciter be found?
It can be found on an electrical generator set. It is used to supply the DC voltage for the field coils.
What is the function of the governor of a generator and how exactly is it different from the AVR?
Automatic voltage regulator (AVR) : Depends on the generator output voltage & out put current/Kvar it will change the exciter voltage. Change in excitation voltage controls the reactive power (Kvar). whereas, a Governor controls the fuel supply to primemover(Engine) in order to control the speed of generator, change in speed (rpm) also controls Active power (KW).
What does voltage do?
A 'voltage source' is a general term, for anything that can supply electrical power.It can be a battery, generator, solar panel etc.It is mentioned on schematics and other diagrams, to show where the power is applied.
Why is it that a 2000 watt Honda EU generator not power a 1140 watt high pressure sodium fixture?
The first thing that comes to mind is check the voltage of the HPS ballast. Some ballasts have multi taps so that a variety of voltages can be used to operate the fixture. Make sure that you have connected the generator's supply to the 120 volt tap. Make sure that the generator's breaker is on and that there is the correct voltage at the output. If is is a dual voltage generator make sure that you are plugged into the correct voltage output.
Can you install 60 amps generator and only get 50 amps AC power at 110 - 240 volts?
If you need 50 amps you can use a 60 amp generator or any other generator rated to supply more amps. The voltage, 110 v or 240 v, must be the right voltage for the load used.
Can a generator be a motor?
Usually, yes! You will need some kind of variable/low voltage supply (recommended either of those 2) and slowly turn up the voltage. If you notice it moving, then it will work. If it just buzzes and sits there, immediately cut off the voltage so you don't burn out your generator. Be careful, the maximum input voltage of it isn't usually measured since it's a generator, so while still on the variable supply, test and see when the brushes start to throw some decent sparks, at that point you should stop and whatever voltage that was should be your maximum after you subtract 8 volts or so.
