answersLogoWhite

0

If the exposed wire grounds out and a great amount of heat is produced then yes a fire could start under this condition. Remember overhead transmission wires are exposed wires but are well insulated from ground so as not to have the above scenario happen.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Electrical Engineering

Can a cut Grounding wire will starts a fire?

No. Get is connected as soon as possible for safety's sake.


Which electrical wire to cut black or white?

Black is hot and white is neutral. If you are switching something you switch the black, so that is what you would cut.


What fire extinguisher do you use on a electrical fire?

Water is good as it will cut off oxygen and cool the heat source. Powder and foam will smother to cut off oxygen. Carbon Dioxide (CO2) will cut off oxygen but blast of gas may spread ther fire by blowing light material such as paper causing it to set fire to other things. Don't use water on oil, or a chip pan fire.


How can you cut an energized conductor?

With an insulated handle wire cutter.


How EDM wire cut machine works?

in wire cut, a wire is passed through a metal or is placed next to it. the wire works as one of the electrodes while the work piece would be the other one; using andielectric liquid to isolate the wire from the work piece. the electricity is conducted in the wire. as the wire gets closer to the work piece the electricity (electrons) tend to jump from the wire to the work piece in order to create a complete electrical circuit that's when a spark is formed. the dielectric helps us by isolating the wire from the work piece as long as it can, so we can have enough difference in potential between two electrodes before the spark is formed, it works like capacitor stopping the current from going through it until it collapses at a potential and enough current passes through at once. A collateral effect of this passage of current is that material is removed from both the electrodes.

Related Questions

Why the fuse wire reduces the danger of fire in a building?

A short in an electrical circuit could cause the cables to become red hot, causing an electrical fire. Before the cables begin to heat up, the thinner fuse wire will blow, or a breaker will trip, and the circuit will become open before any damage occurs.


Can a cut cable wire cause a fire?

If by 'cable wire' you mean Coax cable for the TV, or Internet, then the answer is no. The power/voltages in the cable are way to low to produce a spark which is usually what triggers flame. If by 'cable wire' you mean a cable carrying an electrical service such as 120V or 240V, then, if the cable is damaged by an accidental or deliberate cut which causes a short circuit from a hot phase wire or wires to other wires in the cable - such as to other hot phase wires in a 3-phase circuit, a neutral or a ground wire - then the resulting heavy current could result in the cable becoming very hot and could cause it to catch on fire unless there was some overcurrent protection device to prevent that from happening. That is why fuses and/or circuit breakers should always be included in any electrical service wiring to cut off the supply of current before a fire can be caused by such damage.


What is the proper technique that wire strippers use to remove the insulation from electrical wires?

To remove insulation from electrical wires using wire strippers, place the wire in the appropriate gauge slot, squeeze the handles to cut through the insulation, and then pull the insulation off the wire. Be careful not to cut into the wire itself.


Can you cut el wire?

Yes, you can cut EL wire to shorten it to the desired length. Just make sure to seal the cut end properly to avoid any electrical issues.


What would cause starter relay fuse to blow when trying to start 1997 expedition?

An Electrical Short Cut somewhere would cause it to blow the fuse. A pinch wire would ground the system, and cause a shortcut.


What are the function of wire stripper?

They are for stripping the insulation off electrical wire.


Can a cut Grounding wire will starts a fire?

No. Get is connected as soon as possible for safety's sake.


Which electrical wire to cut black or white?

Black is hot and white is neutral. If you are switching something you switch the black, so that is what you would cut.


How can I effectively perform wire repair to fix a damaged electrical connection?

To effectively perform wire repair for a damaged electrical connection, follow these steps: Cut out the damaged section of the wire. Strip the insulation from the ends of the wire. Twist the exposed wire ends together. Solder the twisted wire ends for a secure connection. Insulate the repaired area with electrical tape or heat shrink tubing.


How can I repair a damaged electrical wire?

To repair a damaged electrical wire, first turn off the power source. Cut out the damaged section of the wire and strip the insulation from the ends. Connect the wires using wire connectors or soldering them together. Insulate the connection with electrical tape or heat shrink tubing. Finally, test the repair to ensure it is working properly before restoring power.


How can I safely and effectively cut cable wire without causing any damage or injury?

To safely and effectively cut cable wire without causing damage or injury, follow these steps: Turn off the power source to the cable wire. Use insulated tools to cut the wire. Wear protective gear such as gloves and safety goggles. Make sure to cut the wire cleanly and avoid any nearby electrical components. Double-check that the power is off before cutting the wire.


How can a wire stripper be used to safely and efficiently remove insulation from electrical wires?

A wire stripper can be used to safely and efficiently remove insulation from electrical wires by adjusting the cutting depth to match the thickness of the insulation, then gripping the wire and rotating the stripper around it to cut through the insulation without damaging the wire underneath.