0
You can add as many light fixtures as you want to the existing switching setup, provided that doing so does not cause you to overload your circuit. To be safe, identify which fixtures and receptacles are on that circuit, and make sure the total connected wattage is no greater than 1440 watts (for a 15A breaker) or 1920 watts (for a 20A breaker). These values incorporate a safety factor by only allowing the circuit to carry 80 percent of the circuit breaker's value. If the total connected wattage is (or will be, by adding the new fixture) over that limit, you'll need to call an electrician to get another circuit and split up your load.
What else can I help you with?
How do you hook up a light and switch from an existing light?
Add a light to switch from a different circuitI think here your concern is that you don't want change the performance of the circuit to which you add the light.so you have to use a relay or a solid state relay to the circuit and a separate power supply to the light in compliance with all the safety rules.
How do you add a switch to a outlet?
ask them how
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
You have just replaced your ceiling light and when you turned the power back on the light stays on even when you turn off the switch?
Re open the switch junction box after turning the power back off. If you can locate the wire that bring the voltage to the box make sure that this wire goes to the top of the switch. If it is tied into more black wires this could be receptacle circuits that are on all of the time. If this is the case, from this group add a pigtail from this group to the top of the switch. from the bottom of the switch find the wire that is going to the light. It is probably in the group that is tied together. Once found terminate this wire to the bottom of the switch. Put the breaker back on and try the switch.
How can you wire and control 3 lights from 1 switch?
This is simple. First the wire coming from the power supply go to the switch. Then it goes to the first , the second and the third light. Since the switch comes first all three light will be controlled by that one switch.
How do you add another porch light to an existing switch?
Piggyback off the box for the existing light. Run a wire from the existing junction box to a new junction box (which is placed wherever you want the new fixture). Then, in the existing box, connect the wire coming from the switch, the wire for the existing fixture, and the wire for the new fixture together using wire nuts. Wire up the new fixture, and presto, you have two fixtures on a switch where there was only one before.
How can I add an outlet from a light switch?
To add an outlet from a light switch, you will need to connect the outlet to the existing wiring of the light switch. This involves turning off the power, removing the switch cover, identifying the hot and neutral wires, and connecting them to the outlet. It is important to follow electrical safety precautions and consult a professional if you are unsure.
How can I add a light switch to an existing circuit?
To add a light switch to an existing circuit, you will need to first turn off the power to the circuit at the breaker box. Then, identify the hot wire in the circuit and connect it to one terminal of the switch. Connect the other terminal of the switch to the light fixture. Finally, connect the neutral wires together. Make sure to follow all safety precautions and consult a professional if needed.
How do you hook up a light and switch from an existing light?
Add a light to switch from a different circuitI think here your concern is that you don't want change the performance of the circuit to which you add the light.so you have to use a relay or a solid state relay to the circuit and a separate power supply to the light in compliance with all the safety rules.
How can I add a light switch to a room?
To add a light switch to a room, you will need to first turn off the power to the room at the circuit breaker. Next, determine the location for the switch and cut a hole in the wall for the switch box. Connect the switch to the existing wiring, making sure to match the wires correctly. Secure the switch in the box and cover it with a switch plate. Finally, turn the power back on and test the switch to ensure it is working properly.
How can I add a dimmer switch to control the lighting in my room?
To add a dimmer switch to control the lighting in your room, you will need to first turn off the power to the room at the circuit breaker. Then, remove the existing light switch and replace it with a dimmer switch. Follow the manufacturer's instructions for installation and wiring. Once installed, you can adjust the dimmer switch to control the brightness of the lights in your room.
I have a light that turns on the basement light. I'd like to change that light switch to add a second light on the stairs that will operate separately from the basement light. What do I do?
Tie into the line side (always hot) of the first switch. Run 12-3 to the second switch and then tie the load side of the second switch to your second light. Assure you have all the proper hardware and supports. Turn off all power prior to working on it cause electricity is dangerous. If you are close to your panel its always safest to run a new circuit since you have a limit on how many things can be on one circuit based on your wire size.
How do you add a second toilet to an existing drain?
All you have to do is add a "Y" pipe or Call a plumber
How do you add a light switch to a ceiling fan that doesnt have a pull switch. i installed a light kit but theres no way to turn off the light. do i drill a hole and add a switch to existing wiring?
Some brand fans have a remote control kit that installs in the fan housing. Also if you have access you can run a separate switched voltage to the fan. In this case you would have to put a second switch in the same box that controls fan, unless it is a switch with speed control that came with fan. In this case you would have to install a new box (Old Work Switch Box from Home Depot or Lowes for example) and run voltage to the box, install a switch and run wire to fan and connect to light. One other possibility is to check the ceiling box and see if there is a spare red wire. If so you could use this to switch power to the light separately from the fan. Again it depends on the switch configuration and supply voltage feed.
How can I add a switch to a light?
To add a switch to a light, you will need to first turn off the power to the light fixture. Then, you will need to run electrical wiring from the light fixture to the location where you want to install the switch. Connect the wiring to the switch and the light fixture following the manufacturer's instructions. Finally, secure the switch in place and turn the power back on to test the switch.
How do you wire a pull switch on a hard wire ceiling light that has no switch?
Two options. Change the fixture to a keyed pull-chain, or add a pull-chain adapter to the existing fixture. Both available from Home Depot and others for about $3.
Is it difficult to add a second sink to a bathroom?
It is not excessively difficult to add a second sink. Make sure that there is enough room for the second sink. If you install the second sink next to the existing one, installing T-fittings to existing plumbing is a good idea. anonymous@oola.com
