0
You have just replaced your ceiling light and when you turned the power back on the light stays on even when you turn off the switch?
Re open the switch junction box after turning the power back off. If you can locate the wire that bring the voltage to the box make sure that this wire goes to the top of the switch. If it is tied into more black wires this could be receptacle circuits that are on all of the time. If this is the case, from this group add a pigtail from this group to the top of the switch. from the bottom of the switch find the wire that is going to the light. It is probably in the group that is tied together. Once found terminate this wire to the bottom of the switch. Put the breaker back on and try the switch.
What else can I help you with?
Why do ceiling fan lights go out?
Without knowing some more facts, there could be several different answers to explain why a ceiling fan's lights "go out":someone has turned them off at the switch for the lights on the fan unit;the light bulbs are "dead" and need replacing because their filaments have broken;there is a fuse protecting the lighting circuit and it needs replacing because it blew from the surge of high current that sometimes happens when a light bulb "dies";there is a timer in the fan unit which turns the lights off after a certain period of time;the wiring from the switch to the light has become disconnected;the switch in the fan that controls the lights is broken and needs to be replaced...
How does power continue to a light if the switch is turned off?
plug it in
To mount two switches and a pilot light in a single gang standard device box you would use?
You would need to purchase a duplex switch. As for the pilot light look for a duplex switch that has a neon pilot light that is incorporated into the handle of the switch. When the switch is turned on the switch's handle will illuminate.
If a light switch that is connected to an outlet which is burnt out and when you replaced the outlet it burnt out within two weeks so how do you change the switch to operate recessed ceiling light?
you must have to much of a load on the outlet or didnt tighten the screws holding the wires tight enough , it should not go out that quickly. if you want to wire it for recess you first have to check if you can get to the location in the attic above the switch. and you need to be able to fish a wire down to the switch up to the recesed lite. which sometimes is not the easiest job to do , better to just call in the electrician for this job
Feed drops to zero volts when light switch is turned on back to 120 volts when turned off feeds fluorescent lights?
voltage is measured by voltagd drops. When a switch is open/ off there is a voltage difference between one side to the other. when the switch is on there is no drop from one side of the switch to the other. That is normal operation. If switch is on, and you get a voltage reading across the switch, the switch is bad.
Why does the ceiling light stay on when the switch is turned off?
When the ceiling light stays on after the switch is turned off, it could be due to a wiring issue where the switch is not properly cutting off the power supply to the light fixture. This can happen if there is a faulty switch, loose wiring connections, or a short circuit in the electrical system. It is important to have a qualified electrician inspect and repair the issue to prevent any safety hazards.
Why is it that my ceiling fan works perfectly fine, but the light attached to it does not turn on?
The issue with your ceiling fan's light not turning on could be due to a problem with the light bulb, the light switch, or the wiring connecting the light to the fan. It is possible that the light bulb needs to be replaced, the light switch is faulty, or there is a wiring issue that needs to be addressed.
Why did you pull the chain out of your ceiling light?
The chain was pulled out of the ceiling light because it was not functioning properly or needed to be replaced.
Where is expedition light switch on rear hatch?
The light switch is located above the hatch door ceiling.
When a light switch is turned on what travels through the wire?
Current flows through a wire when a light switch is turned on.
How can I put a ceiling fan and light on the same switch?
To put a ceiling fan and light on the same switch, you can use a dual-function switch that controls both the fan and light simultaneously. This type of switch allows you to operate both the fan and light with a single switch, simplifying the control of both fixtures.
How do I replace the ceiling fan light switch?
To replace the ceiling fan light switch, first turn off the power to the fan. Remove the light kit cover and locate the switch. Unscrew the switch and disconnect the wires. Connect the new switch and secure it in place. Test the switch before reassembling the light kit cover.
Can I get my ceiling fan to turn on and off by using the light switch?
Yes. Simply turn on the ceiling fan while the light switch is in the "on" position. Adjust the spinning to the level of your choice. Now the fan will turn on and off when you switch the light on and off.
How do you operate a pull switch ceiling light?
To operate a pull switch ceiling light, simply pull the attached cord or chain downwards to turn the light on. Pull the cord or chain again to turn the light off.
Why does a light switch get hot when turned on?
A light switch can get hot when turned on because of the flow of electricity through the switch. This flow of electricity causes resistance in the switch, which generates heat as a byproduct.
How can I install a ceiling fan dimmer to control the brightness of my ceiling fan's light?
To install a ceiling fan dimmer to control the brightness of your ceiling fan's light, follow these steps: Turn off the power to the ceiling fan at the circuit breaker. Remove the existing wall switch that controls the fan's light. Connect the dimmer switch's wires to the corresponding wires in the wall box. Mount the dimmer switch in the wall box and secure it in place. Turn the power back on and test the dimmer switch to ensure it controls the brightness of the ceiling fan's light.
How can I wire a ceiling fan with a light switch using a diagram?
To wire a ceiling fan with a light switch, follow these steps: Turn off the power to the circuit at the breaker box. Install the ceiling fan bracket to the ceiling. Connect the fan wires to the corresponding wires in the ceiling box (usually black to black, white to white, and green to ground). Connect the light kit wires to the corresponding wires in the ceiling box (usually blue to black and white to white). Install the fan blades and light kit. Install the light switch and connect the wires (usually black to black, white to white, and ground to ground). Turn the power back on and test the fan and light switch. For a visual guide, refer to the diagram below: Diagram of ceiling fan wiring with light switch
