0
Yeah, of course. Nowadays a lot of the wires going to houses are underground in cement.
However - you should not bury the wire / cable directly in the cement - over time the chemicals from the cement will attack the cable and destroy the insulation. The cable must be inserted into a protective tube called 'conduit'. Mostly these days plastic conduit is used, but check local building regulations - in some locations and circumstances metal conduit may be required. It is also possible to purchase 'armoured cable' and use this, it is mostly used to bury cables where there is some risk of physical damage such as from someone digging, it is expensive.
What else can I help you with?
In an IEC-320 plug which wire carries electrical voltage?
the hot wire carries the electrical voltage
Can you run a 240v wire from the electrical panel then put a junction box to run it where you want?
A 240 volt wire is the insulation factor of the wire. If you mean a 240 supply source from a distribution panel to a junction box then the answer is yes. You have to keep in mind that the box has to be accessible, meaning that you can get to the box to check the splice within the box. Don't bury the junction box behind the wall board.
A jumper wire should be used to bridge the electrical ground across?
A jumper wire should use to bridge electrical ground across?
How do you complete a sentence that begins with 'Electrical wire sheathing should not'?
Electrical wire sheathing should not project more than about one inch into the electric panel.
What does the number size on electrical wire indicate?
The number size on electrical wire, often referred to as the American Wire Gauge (AWG), indicates the wire's diameter and, consequently, its capacity to carry electrical current. A lower gauge number signifies a thicker wire that can handle more current, while a higher gauge number indicates a thinner wire with less current-carrying capacity. This sizing is crucial for ensuring safety and efficiency in electrical installations, as using the correct gauge helps prevent overheating and potential fire hazards.
What is the use of cement?
To bury children who don't do their science homework
How can I safely and effectively run underground electrical wire?
To safely and effectively run underground electrical wire, follow these steps: Plan the route carefully to avoid obstacles and ensure proper depth. Dig a trench at least 18 inches deep and wide enough for the wire. Use PVC conduit to protect the wire and prevent damage. Install warning tape above the conduit to indicate its presence. Bury the conduit and wire, making sure to backfill the trench properly. Test the wire to ensure it is functioning correctly before connecting it to the electrical system.
Which wire is the common wire in a typical electrical circuit?
The common wire in a typical electrical circuit is the neutral wire.
What do you call an electrical wire that is not insulated or covered?
The electrical terminology of a wire with no insulation on it is a bare wire.
How can I extend the length of an electrical wire using an electrical wire extender?
To extend the length of an electrical wire, you can use an electrical wire extender. This device allows you to connect two wires together securely, effectively increasing the overall length of the wire.
Is the black wire in this electrical circuit designated as the hot wire or the neutral wire?
In an electrical circuit, the black wire is typically designated as the hot wire.
Is the white wire in this electrical circuit designated as the hot wire or the neutral wire?
In an electrical circuit, the white wire is typically designated as the neutral wire.
How to properly bury electrical wire to ensure safety and compliance with regulations?
To properly bury electrical wire for safety and compliance with regulations, follow these steps: Dig a trench at least 18 inches deep for residential wiring or deeper for commercial applications. Use PVC conduit or direct burial cable rated for underground use. Place warning tape above the wire to indicate its presence. Install a ground fault circuit interrupter (GFCI) for added protection. Have the installation inspected by a qualified electrician to ensure compliance with local codes.
Which wire is typically considered the hot wire in electrical wiring, the black wire or the white wire?
The black wire is typically considered the hot wire in electrical wiring.
How do you remove cement from the body of your car?
wet a rag pour a can of coke on it and then rub it on the cement. then get a stiff wire brush and then rrub it against the cement
What is the difference between a line wire and a load wire in electrical wiring?
A line wire carries electrical current into a device, while a load wire carries electrical current out of a device.
Is cement flooring a good ground or not?
A: Definitely not cement is not a very good electrical conductor of electricity
