0
What else can I help you with?
What is the voltage of high tension electrical transmissions towers?
Usually HV is 33KV and 66KV, EHV is 132KV, 220KV and 400KV and UHV is 800KV and 1200KV
Why is the rating of transformer is like 11kv 33kv 66kv?
Because the tranformer calculation for ratings is calculated with the formfactor which is 1.11 constant. Regards Mithin kudva
How many volts can transmission wire carry?
Transmission voltages are usually considered to be 110 kV and above. Where higher capacity is needed the line conductors are grouped in to three and four groups per phase leg. Voltages less than 33 kV are usually used for distribution by the utility companies.The utility company then supplies the transformers to drop the voltage even lower so that it can be brought to homes to be used by their customers.The transmission lines are of a composite arrangement. ACSR, Aluminium Conductor Steel Reinforced.
How many suspenssion type insulation used in 66kv transmission line?
one insulator unit can bare 11kV. such that 66kV tx line needs 6 insulator units.
What is maximum transmission voltage in Pakistan?
It is 500kv between rahim yar khan and multan.
What is the voltage coming out of a station?
Depends on the sub station. It could be 11KV, 33KV, 66KV,110KV, 220KV, 400 KV etc
What is the Phase to phase voltage of 66KV earthed cable?
Nominal transmission and distribution voltages are line voltages. So '66 kV' is a line-to-line voltage. Note that there is no such thing as a 'phase-to-phase' voltage -the correct term is 'line-to-line'. Using the term, 'phase-to-phase', indicates a lack of understanding of a.c., which is not uncommon! Incidentally, the symbol is 'kV', not 'KV'.
What is the voltage of high tension electrical transmissions towers?
Usually HV is 33KV and 66KV, EHV is 132KV, 220KV and 400KV and UHV is 800KV and 1200KV
Why is the rating of transformer is like 11kv 33kv 66kv?
Because the tranformer calculation for ratings is calculated with the formfactor which is 1.11 constant. Regards Mithin kudva
What is Procedure the procedure to select CT's and PT's in 66kV and above substation?
You need to required following data Voltage Level, Current, Protection Class, SC Current
What is the minimum height for high power lines over a road?
On 11-66kV not less than 5,5 metres,with hazard signs on both sides indicating height of line.
What is difference between lt and ht pannel?
lt pannel is a iow tensan pannel. lt pannel work is 240v and 440v. ht pannel is a high tensan pannel . ht pannel work is 11kv,33 kv ,66kv, 120kv
Where can use voltage of 415v 11kv 66kv 33kv and 132kv?
These are the nominal voltages used by the UK's distribution system, although (to comply with European Harmonisation requirements, 415 V has now been 'replaced' with 400 V. Incidentally, the symbol for the volt is a capital 'V', not a lower-case 'v'.
Why the generating transformers are in 66kv?
As we all know that at the generating station if the the voltage ratings are at higher level like 66 KVto 132 KVso due to it we can obtain a good transmission line with a lower voltage drop and also the voltage ratings can be decreased with the help of step up or step down transformer upto10% very easily at the receiving station.Thanks & RegardsMithinKudva
How many volts can transmission wire carry?
Transmission voltages are usually considered to be 110 kV and above. Where higher capacity is needed the line conductors are grouped in to three and four groups per phase leg. Voltages less than 33 kV are usually used for distribution by the utility companies.The utility company then supplies the transformers to drop the voltage even lower so that it can be brought to homes to be used by their customers.The transmission lines are of a composite arrangement. ACSR, Aluminium Conductor Steel Reinforced.
