answersLogoWhite

0

Can lights have a junction box attached to them. So yes.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you wire in a pull chain switch in a bathroom light fixture?

If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.


Is it easy enough to change an electric light fixture that I can do it without hiring a contractor?

It can be dangerous my dad does it but you need to turn the power off.


Do you need a neutral at every switch 3 way or 4 way included?

No, the neutral is only needed at the load. This is where the connection is made to the light fixture.


Can you use 14-2 wire to operate a ceiling fan using two switches one for the fan the other for the lights?

On these types of installations an electrician would use a three wire cable set from the switch box to the fixture's junction box. At the fixture's junction box both the fan neutral and the light neutral would be wire nutted together with the incoming neutral from the switch boxes. From the three wire, the white wire would go to the fan and light's neutral wires. The Black would come from the bottom of one of the switches and go to the fan's motor lead. The red wire would come from the bottom of the other switch and go to the light fixture's lead. It can be done with two runs of two wire to the fixture. You will need a two gang switch box for this project to hold the two separate switches. You could use a single gang light switch box if you can still find where duplex switches being sold. A duplex switch is one that has the configuration of a duplex receptacle with the switches being one on top of the other. The cover plate is the same one used for duplex receptacles. To answer this question fully more information is needed. See discuss in the left margin.


What size transformer do i need for a dazor floating fixture model?

The sizing of transformers without knowing the input supply voltage and output fixture voltage can not be done. Also needed is the amperage of the floating fixture.

Related Questions

How can I convert a light fixture into an outlet?

Converting a light fixture into an outlet involves disconnecting the wires from the fixture and connecting them to an outlet. You may need to install a junction box and follow electrical safety guidelines. It is recommended to consult a licensed electrician for this task to ensure proper installation and safety.


I have a horizontal junction box with holes on either side to screw in light fixture. Bought a light fixture and the holes do not match up. Do I need a different shape box?

You may either need a different shape box or an adapter plate to properly align the holes with your new light fixture. It's important to ensure that the junction box is compatible with the chosen light fixture for safety and proper installation. Consulting with a professional electrician can also help determine the best solution for your specific situation.


How can I hang a light from the ceiling?

To hang a light from the ceiling, you will need to first locate a suitable electrical junction box in the ceiling. Next, install a mounting bracket to the junction box and secure it in place. Then, connect the wires from the light fixture to the corresponding wires in the junction box, following the manufacturer's instructions. Finally, attach the light fixture to the mounting bracket and secure it in place. Be sure to turn off the power before starting and consult a professional if you are unsure about any steps.


What type of light bulb do I need for my fixture?

You need to use the appropriate wattage and type of light bulb recommended for your fixture. Check the fixture's label or manual for the specific requirements.


What are the necessary steps for installing a light junction box in a room?

To install a light junction box in a room, you will need to follow these steps: Turn off the power to the room at the circuit breaker. Choose a suitable location for the junction box on the ceiling or wall. Cut a hole in the ceiling or wall to accommodate the junction box. Run electrical wires from the existing power source to the junction box. Secure the junction box in place using screws. Connect the wires to the terminals in the junction box, following the manufacturer's instructions. Install the light fixture onto the junction box. Turn the power back on and test the light to ensure it is working properly.


How can I use a can light adapter to convert a recessed light fixture into a pendant light fixture?

To convert a recessed light fixture into a pendant light fixture using a can light adapter, you will need to remove the existing recessed light trim and bulb, then install the can light adapter into the recessed housing. Next, attach the pendant light fixture to the adapter according to the manufacturer's instructions. Finally, adjust the pendant light height and secure it in place to complete the conversion.


How do you convert a swivel recessed light to accept the pendant light kit?

To convert a swivel recessed light to accept a pendant light kit, you will need to remove the existing recessed light fixture and install a pendant light fixture in its place. This typically involves disconnecting the wiring for the recessed light and attaching it to the pendant light fixture according to the manufacturer's instructions. You may also need to install a mounting bracket to support the pendant light fixture.


How can I change a recessed light to a pendant light?

To change a recessed light to a pendant light, you will need to remove the recessed light fixture, install a pendant light fixture in its place, and connect the wiring according to the pendant light's instructions.


How can I install a 3-way switch for a light fixture with the light in the middle?

To install a 3-way switch for a light fixture with the light in the middle, you will need to connect the switches and the light fixture using three-way wiring. This involves running a three-wire cable between the switches and the light fixture, and properly connecting the wires to the switches and the light fixture. It's important to follow the wiring diagram for 3-way switches to ensure the switches work correctly to control the light fixture from two different locations.


How can I add a switch to a light?

To add a switch to a light, you will need to first turn off the power to the light fixture. Then, you will need to run electrical wiring from the light fixture to the location where you want to install the switch. Connect the wiring to the switch and the light fixture following the manufacturer's instructions. Finally, secure the switch in place and turn the power back on to test the switch.


How can I convert a light fixture to an outlet?

To convert a light fixture to an outlet, you will need to disconnect the wires from the light fixture and connect them to an outlet instead. This may require some electrical knowledge and tools. It is recommended to consult a professional electrician for safety and proper installation.


How can I wire an outlet from a light fixture?

To wire an outlet from a light fixture, you will need to connect the outlet to the wiring of the light fixture. This involves running a new wire from the light fixture to the outlet, making sure to follow proper electrical safety procedures and regulations. It is recommended to consult a licensed electrician for assistance to ensure the job is done correctly and safely.