0
-| |--| |--| |-
I don't think Wiki Answers is a viable alternative to paying attention in class
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What are the laws of series and parallel connection?
1.In series connection the total resistance is equal the total number of resistor that was connected in series 2.the current is constant in a series connection 3.in a series connection total voltage is equal the number of of volt per cells
3 ways to reduce power supply ripple?
Increase filter capacitors. Series inductors Semiconductor regulator 3 phase lines instead of single phase
Draw internal connection diagram of 3 point face plate starter?
We cannot display diagrams
What is the total capacitance of a circuit with three capacitors connected in series with the following values C1 015 fd C2 015 fd and C3 015?
It looks like all three of your capacitors have the same value. So the effective capacitance when they're all conected in series is 1/3 of that value = 0.005 fd.
What is the current in a circuit with 9 volts 3 ohms 2 ohms and 4 ohms?
The current in the circuit will depend on how the three resistors are wired. Series? Parallel? Series parallel? With the resistors in series, 3, 2 and 4 ohms will add to 9 ohms. As I = E/R, I = 9 V / 9 ohms = 1 A. With the resistors in parallel, the 3, 2 and 4 ohm resistors will draw 3 A, 4.5 A and 2.25 A respectively, and the total current will be the sum of the branch currents, or 3 A + 4.5 A + 2.25 A = 9.75 A. There are 3 different series parallel circuits possible, and more investigation will be necessary to solve for them.
How do you draw a circuit diagram with a series connected to a parallel?
--------------[res 1---]------------|-----------------|| | || [res 2] [res 3]| | || | |--------------------------------------------------------res 1 is in series with a parallel connection of res 2 and 3. This is just one example.
What are the laws of series and parallel connection?
1.In series connection the total resistance is equal the total number of resistor that was connected in series 2.the current is constant in a series connection 3.in a series connection total voltage is equal the number of of volt per cells
3 ways to reduce power supply ripple?
Increase filter capacitors. Series inductors Semiconductor regulator 3 phase lines instead of single phase
Draw internal connection diagram of 3 point face plate starter?
We cannot display diagrams
What is the total capacitance of a circuit with three capacitors connected in series with the following values C1 015 fd C2 015 fd and C3 015?
It looks like all three of your capacitors have the same value. So the effective capacitance when they're all conected in series is 1/3 of that value = 0.005 fd.
What are the uses of series connection?
Disadvantage of series connection: 1.If one point breaks in the series circuit, the total circuit will break. 2.suppose if you want to connect 3 bulbs rated 230v,5A in series then due to added up resistance less current flows and the bubs are dimmer
Who won the England vs West Indies test series in 2007?
England won the Series 3-0, the Lords test being the only draw in a 4 test series.
Why does delta's connection draw high current?
For the same amount of power, a star or delta connection will use the same line current. However a delta connection supplies sqrt(3) times less current to the device on each of its connections because the voltage is sqrt(3) times more. The apparent contradiction comes about because in a delta connection each connection to the line is shared between two connections to the device (Historikeren 20-07-2015).
Where would power factor capacitors be installed on a 3 phase motor?
Power factor capacitors can be installed on a three phase motor between the motor contactor and the overload heater block.
Is there a minimum derated voltage that tantalum capacitors should be operated at?
Yes, 1/3
Can you draw a square with 3 lines?
you draw a square with 3 lines inside it.
How would the hook up 3 resistors in a circuit to get a maximum current?
In series, R = R1 + R2 + R3 + ... The current in a series connection will only have 1 path. The current is the same through each resistor
