0
A variety of techniques can be used. Node-Voltage and Mesh-current (or Loop-current) methods, for example. See related link for examples. If there is a single voltage source in the model, then find the current supplied, and Resistance = Voltage/Current. {R = V/I}
You could simulate/ model the circuit on a computer then apply the power profile and a current value will be calculated. Or if you have the circuit working, Place an amp meter into the circuit and measure the current. V/i = resistance.
What else can I help you with?
How do you calculate the joint resistance in a series circuit with three resistances?
The resistance of a series circuit is simply the sum of the individual resistors.
The value of resistance of an short circuit?
The value of resistance when there is a short circuit varies depending on the nature of the fault, but it could be fractionally above zero or higher.
What would happen to circuit if there was no resistance?
a circuit with no resistance or zero resistance can be considered as open circuit in which the current is zero. without resistance the circuit just becomes open ()
How do you find resistance when you have current and resistance total?
If you are looking for the resistance of each resistor in either a series circuit or a parallel circuit you must measure the current I and the voltage V for each resistor. Then calculate its resistance using Ohms Law R = V / I where I = current (Amps), V = voltage (Volts) and R= resistance (Ohms).
Is the increase in voltage causes a greater electric resistance in a circuit?
No, the resistance in a circuit does not change when voltage changes. Resistance is an inherent property of the circuit.
What is the net resistance of the circuit connected to the battery in the figure?
To find the net resistance of the circuit connected to the battery in the figure, you need to calculate the total resistance by adding up the individual resistances in the circuit.
How do you calculate the joint resistance in a series circuit with three resistances?
The resistance of a series circuit is simply the sum of the individual resistors.
How to figure amps in an electrical circuit?
To figure out the amps in an electrical circuit, you can use Ohm's Law, which states that Amps Volts / Resistance. Measure the voltage across the circuit and the resistance of the components in the circuit, then divide the voltage by the resistance to calculate the amperage.
Why isn't resistance constant?
If measuring resistance of materials or resistors by themselves(not soldered into a circuit board) resistance is constant. If measuring resistance of a circuit then it could fluctuate with the components functioning in the circuit.
How do you calculate the equivalent resistance in a parallel circuit?
To calculate the equivalent resistance in a parallel circuit, you use the formula: 1/Req 1/R1 1/R2 1/R3 ... 1/Rn, where Req is the equivalent resistance and R1, R2, R3, etc. are the individual resistances in the circuit.
How do you calculate amps in an electrical circuit?
To calculate amps in an electrical circuit, you use Ohm's Law, which states that Amps (I) Volts (V) / Resistance (R). This formula helps you determine the current flowing through the circuit based on the voltage and resistance present.
What is common to both thevenin and norton theorem?
To solve any D.C. circuit by using Thevenin Theorem,First of all load resistance RL is disconnected from the circuit and open circuit voltage across the circuit is calculated (known as Thevenin equivalent voltage)Secondly, the battery is removed by leaving behind its internal resistance. Now we calculate equivqlent resistance of the circuit ( called Thevenin equivalent resistance).Now we connect Thevenin Voltage in series with Equivalent resistance of the circuit and now connect load resistance across this circuit to calculate current flowing through the load resistance.Whereas in the case of using Norton theorem, we again remove the load resistance if any, and then short circuit these open terminals and calculate short circuit current Isc.Second step is same as in Thevenin theorem i.e. remove all sources of emf by replacing their internal resistances and calculate equivqalent resistance of the circuit.Lastly, join short circuit current source in parallel with equivalent resistance of the circuit. Now, we can calculate votage across the resistance which was connected in parallel with Isc.So, by knowing the open circuit voltage, we can calculate current flowing the resistance and on the other hand , by knowing the short curcuit current , we can calculate voltage across the resistance.
An open circuit has an infinate resistance?
There is no such a thing as infinite resistance but it could be a very high resistance.
How to calculate the current in a circuit?
To calculate the current in a circuit, you can use Ohm's Law, which states that current (I) equals voltage (V) divided by resistance (R). The formula is I V/R. Simply plug in the values for voltage and resistance to find the current flowing through the circuit.
How to calculate amps in a circuit?
To calculate amps in a circuit, use the formula: Amps Volts / Ohms. This formula helps determine the current flowing through a circuit based on the voltage and resistance present.
How do you calculate the voltage in a circuit with a resistance of 20hms and a currents of 6?
Use Ohm's Law. In this case, multiply the resistance by the current.
How to determine amp draw in an electrical circuit?
To determine amp draw in an electrical circuit, you can use Ohm's Law, which states that current (amps) equals voltage divided by resistance. Measure the voltage across the circuit and the resistance of the components in the circuit, then divide the voltage by the resistance to calculate the amp draw.
