This is a very simple procedure for the average home owner. First remove the voltage source from the switch by turning off the breaker for that switch circuit at the distribution panel. Remove the two screws that hold the cover plate on.
Remove the two switch holding screws and pull the switch forward so that you can get to the side terminals.
On a piece of paper make a note of where and what colour the wires are and the position of where they are terminated to on the existing switch.
Some new switches have a ground terminal, if the old one did not, extend the ground wire from the back of the switch's junction box and connect to the switch's ground terminal.
Remove the old switch and replace with the new switch.
Reconnect the switch referring to your notes.
Install the switch into the junction box, turn the switch to the off position and replace the cover plate.
Turn the circuit breaker on that feeds the switch circuit.
Turn the light switch on to test the completed lighting circuit.
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself, on electrical circuits, equipment or appliances always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB SAFELY AND COMPETENTLY REFER THIS WORK TO QUALIFIED PROFESSIONALS.
A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.
The switch sounds like it might be arcing. Switches are inexpensive, change it out with a new one. With the power off and the old switch removed check the connections in the switch junction box for loose splices or burnt wire nut connectors. If everything is fine there check the light junction box for loose connections.
There are multiple ways to wire a switch. If power is fed into the switch box, a second light would be wired one way, if power is fed into the light box, the second light would be wired a different way. This seems like it would be a task better given to a qualified electrician or local handyman.
Each 3 way switch has 2 sets of contacts connected internally to a common pole (marked COMMON). Inside the switch are a set of normally closed (NC) and normally open (NO) contacts. Electrical normally closed contacts pass power unlike plumbing in which a normally closed valve blocks air or fluid flow.
"How does a single pole switch differ from a three way?" is a trick question often asked to catch-out new trainee electricians because the common but mis-named "three-way switch" is actually a single pole, double throw switch, i.e. it is only a 2-way switch, not a 3-way switch.A pair of "3-terminal, single pole, double throw" switches are often used to hook-up two separate light switches to control one light or one set of lights.A proper "3-way switch" would be capable of being switched to 3 different positions and could have one, two or more poles. Each pole could be either single- or double-throw.The same answer put in a different wayDespite the fact that the name "3-way switch" is often used to describe it, if it is of the type that has just one pole that can only be physically switched 2 ways, the name "3-way switch" is quite wrong for that particular switch. A "3-terminal, single pole, double throw" switch" is a more accurate description for it.Comment'Three-way switch' -American term. 'Two-way switch' -UK term for the same type of switch. Used to operate a lamp from two different locations.
A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.
Send power to the 1st switch and then send the power from that switch when it is in the on position to the second switch. Then send power to the light from the second switch. That way both switches will have to be in the on position for the light to be on.
To control 2 lights with 2 switches in a single circuit, you can use a three-way switch setup. Connect one switch to the power source and the first light, then connect the second switch to the first light and the second light. This way, you can control both lights independently with the two switches.
By 2 way switch I assume you mean a single pole switch. If so yes this can be done.
To change a light switch with 2 wires, first turn off the power to the switch at the circuit breaker. Remove the cover plate and unscrew the switch from the wall. Disconnect the two wires from the old switch and connect them to the new switch, making sure to match the wire colors. Screw the new switch back into place, replace the cover plate, and turn the power back on at the circuit breaker.
You don't. You use a pair of two-way switches ('three-way switches' in US/Canada).
No, a 3-way switch cannot be used as a 2-way switch because they are designed for different functions.
To light up the bulb, the two-way switch must be closed in the on position at both the 'Switch 1' location and the 'Switch 2' location. This will complete the circuit and allow electricity to flow to the light bulb, turning it on.
Here are three diagrams that illustrate how to wire a three-way switch correctly. Diagram 1: Shows the wiring connections for two three-way switches controlling a single light fixture. Diagram 2: Demonstrates the wiring setup for a three-way switch with a light fixture at the end of the circuit. Diagram 3: Illustrates the wiring configuration for a three-way switch with power at the light fixture. These diagrams will help you understand the proper wiring techniques for a three-way switch setup.
To wire 2 3-way switches to control a single light fixture, you will need to connect the switches in a specific way. The power source should be connected to the first switch, then a traveler wire should be connected between the two switches. Finally, the light fixture should be connected to the second switch. This setup allows you to control the light fixture from either switch.
The switch sounds like it might be arcing. Switches are inexpensive, change it out with a new one. With the power off and the old switch removed check the connections in the switch junction box for loose splices or burnt wire nut connectors. If everything is fine there check the light junction box for loose connections.
Probably located at top of brake pedal secured by 2 locknuts and 2 wires