0
Trimmer capacitors are used to calibrate (trim) the capacitance in a circuit. They are connected in parallel with some other capacitor, and the circuit is calibrated by observation of response to known stimuli. Since trimmer capacitors are often used in RF circuits, it is generally not possible to make measurement of the capacitors out of circuit because parasitic capacitance at RF is not negligible.
Additional question received on April 6th: "I have a 3 terminal trim cap; 2 terminals read continuity, the other not. My question is how do I connect this in a circuit?"
In all probability, the two terminals that read continuity are the same terminal, and are simply provided to give three point mechanical stability when soldered into a circuit. You would connect the two terminals that do not have continuity, using either of the terminals that do have continuity, across the capacitor that needed to be "trimmed".
What else can I help you with?
How to connect 3 phase power factor correction capacitor?
how to connect power capacitor with 3 phase motor
How do you connect the capacitor bank in electrical system?
improvement of power factor
How do you wire a compressor capacitor and a fan capacitor?
To wire a compressor capacitor and a fan capacitor, first ensure that the power supply is turned off for safety. Connect the compressor capacitor by connecting its common terminal to the compressor, the herm terminal to the power supply, and the start terminal to the start winding of the compressor. For the fan capacitor, connect its common terminal to the fan motor, the fan terminal to the power supply, and the start terminal to the start winding of the fan motor. Always refer to the wiring diagram specific to your unit to ensure correct connections.
How do you UNCHARGE a capacitor?
Connect it, in series, to a resistor or a dummy load and a switch. And then throw the switch.
How do you connect single phase supply to a two capacitor motor?
See Discuss Question below.
How a trimmer capacitor use?
A trimmer capacitor is a semi-adjustable capacitor placed across a variable tuning capacitor and pre-set to allow the main capacitor to track correctly with another variable capacitor on the same shaft. The adjustment takes out any differences introduced by the connected circuit.
Can you replace a 2-30 trimmer capacitor with a fixed value capacitor?
Yes you can. But the variable one is used so that you can very the frequency and it cant be varied anymore if you use a fixed capacitor.
How to connect 3 phase power factor correction capacitor?
how to connect power capacitor with 3 phase motor
What will happen if you connect 12volt battery to a 240VOLT capacitor?
If the capacitor is charged then the battery will explode.
How do you connect a targa capacitor to your amplifier?
To connect a Targa capacitor to your amplifier, first ensure the amplifier is turned off and disconnected from power. Connect the positive terminal of the capacitor to the positive power terminal of the amplifier, and the negative terminal of the capacitor to the negative power terminal. Finally, connect the capacitor's ground terminal to a solid ground point on the vehicle. Always double-check your connections and polarity before powering the system back on.
What is the function of a capacitor's leads?
To connect it to the circuit.
Can blackberry 8900 connect to tv?
No, you would need an alternating capacitor to connect.
How do you connect a capacitor in simulink?
To connect a capacitor in Simulink, you can use the "Capacitor" block found in the Simscape > Electrical > Specialized Power Systems > Elements library. Drag the block into your model and connect its terminals to the appropriate components, such as voltage sources or resistors, to complete the circuit. Ensure that you configure the capacitor's parameters, such as capacitance value, in the block's dialog box for accurate simulation results. Finally, connect necessary measurement blocks to analyze the capacitor's behavior in the circuit.
How to add a capacitor and resistor in parallel?
To add a capacitor and resistor in parallel, simply connect one terminal of the capacitor to one terminal of the resistor, and then connect the other terminal of the capacitor to the other terminal of the resistor. This creates a parallel circuit where both components share the same voltage.
Why connect capacitor to alternator?
To help produce voltage.
Can a non polarized capacitor be connected to a direct current circuit?
Yes, you can connect a polarized capacitor to a direct current. Make sure you get your polarization is correct.A non polarized capacitor can be connected in a DC circuit as well. "Non Polarized" just means it does not matter which side of the capacitor is positive. If you attempt to connect a polarized capacitor in a DC circuit backwards, you will know when the capacitor explodes.
How do you connect the capacitor bank in electrical system?
improvement of power factor
