answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

What should be the value of capacitor at transistor amplifier circuit input?

at full input, if the transistor is working, the value of capacitor will be 0.


How do you connect digital amplifier to digital amplifier?

You can look at the in and out connectors on the TV and the amplifier. You have choices that depend on the tv and amplifier, basic stereo, surround sound and tos-link. As you know in and out are connected and out and in are connected. Do not connect in and in to each other and do not connect out and out to each other.


What happens when you remove capacitor in filter circuit?

The capacitors allow the signal to pass through, while 'blocking' the DC voltage level that the signal is 'riding' on. Are you asking to remove the capacitor and connect it straight through? If you had a multistage amplifier, then the DC riding voltage would try to get amplified as well, and the next stage amplifier would probably 'max out' and you'd wind up with just solid DC output, or components further along in the circuit could be damaged. If you're asking if the capacitor was taken out (like if it blew) then no signal would get through.


What is different of common emitter amplified with capacitor and without capacitor?

It depends on where the capacitor is located. If it is across the emitter resistor, then the gain of the CE amplifier will be higher at higher frequencies.Remember that gain in the CE amplifier is collector resistance divided by emitter resistance, or hFe, whichever is lower. Placing a capacitor across the emitter resistor will serve to make the effective resistance smaller at higher frequencies, resulting in increased gain, up to the limit of hFe.If this is not the intended location of the capacitor, then please restate the question and provide the capacitor location.


Can you connect a speaker level output from one amplifier to the RCA input of another amplifier?

Yes you can with the converter.Even i have to buy that .

Related Questions

What does a capacitor do in an amplifier circuit?

not sure


What are the steps behind installing a car audio capacitor?

First, the capacitor must be charged. Use a voltmeter, and when it reaches 12 volts, the capacitor is charged. The capacitor should then be installed near the car audio amplifier. Keep the negative wire attached to the battery. Then, a ground wire from the negative post on the capacitor to the car's chassis on the chassis's bare metal ground point. Next, the power wire needs to be disconnected from the amplifier's power input. Connect the wire to the positive post on the capacitor. A new power wire needs to be connected from the capacitor's positive post to the amplifier's power input. Install a 16 gauge wire from the capacitor's remote turn-on post to the amplifier's remote input. Then disconnect the negative wire from the battery.


How to connect 3 phase power factor correction capacitor?

how to connect power capacitor with 3 phase motor


What should be the value of capacitor at transistor amplifier circuit input?

at full input, if the transistor is working, the value of capacitor will be 0.


How do you connect digital amplifier to digital amplifier?

You can look at the in and out connectors on the TV and the amplifier. You have choices that depend on the tv and amplifier, basic stereo, surround sound and tos-link. As you know in and out are connected and out and in are connected. Do not connect in and in to each other and do not connect out and out to each other.


How can I reduce the bass response on my car amplifier?

Try adding a adding a capacitor.


Connect a 12v wire to an amplifier?

Ensure the amplifier is turned off. Connect the positive (+) terminal of the 12V wire to the amplifier's positive terminal and the negative (-) terminal of the 12V wire to the amplifier's negative terminal. Once connected securely, you can then power on the amplifier.


What happens when you remove capacitor in filter circuit?

The capacitors allow the signal to pass through, while 'blocking' the DC voltage level that the signal is 'riding' on. Are you asking to remove the capacitor and connect it straight through? If you had a multistage amplifier, then the DC riding voltage would try to get amplified as well, and the next stage amplifier would probably 'max out' and you'd wind up with just solid DC output, or components further along in the circuit could be damaged. If you're asking if the capacitor was taken out (like if it blew) then no signal would get through.


What is the output resistance of common emitter amplifier with emitter resistor and without bypass capacitor?

Without a bypass capacitor it is just equal to Rc


What is meant by RC coupled amplifier?

an amplifier, where the resistor and capacitor get coupled to provide high oscillations hence by which amplifications increases at high degrees


What will happen if you connect 12volt battery to a 240VOLT capacitor?

If the capacitor is charged then the battery will explode.


How can I connect a microphone to speakers?

To connect a microphone to speakers, you will need an audio mixer or amplifier. Plug the microphone into the mixer or amplifier using an XLR cable. Then connect the mixer or amplifier to the speakers using audio cables. Adjust the volume levels on the mixer or amplifier to ensure proper sound output.