0
If it's low voltage, such as a cable company or telephone company, you should be able to contact them directly and ask them to bury the wire.
If it's a power cable you should contact the electrician who ran the wire or the local power company.
Either way, if you get no results, contact the local building and zoning department; they should be able to help you force a contractor into compliance.
What else can I help you with?
How do you connect the 3 pin plug?
One pin for phase other pin for neutral and third one is for earth/ground wire. In India the right pin is for phase, left pin is for neutral and pin on top side is for ground wire. This third top side pin is slightly bigger and longer compared to phase and neutral pins.
How do you wire a 4way switch?
Connect all white wires together under a wire nut and push them back into the box. Connect all ground wires together and then connect them with a jumper wire to the ground screw on the switch. Connect black power in and power out, if applicable, wires to the bottom screw on the switch. Connect the remaining black wire going to the light to the top screw on the switch.
Where do you ground on 100 amp panel?
A typical panel has three large wires entering the main panel from the electric meter and a bare ground wire. Two of the large wires are hot and go to the busses where the breakers are mounted. The third wire is common and is connected to one or more common bus locations. It will usually be silver in color with a screw on top to connect white wires from branch circuits. The ground is the metal of the panel itself and there will be one or more ground busses usually copper colored that are connected to the metal of the panel by screws there by "bonding" these ground busses to the metal of the panel. You should also see a copper wire coming from a ground rod connected to the metal of the panel. At the main panel you need to bond the common to the ground. There is usually a screw that allows this bonding to occur. If you have subpanels ground and common are NOT connected at the subpanels.
How do you properly ground an electric fence?
You need to have a grounding rod made of galvanized steel that is driven straight into the ground until only half an inch of bar is remaining above ground. The ground rod should be at least 6 feet in length. Drier land areas normally require a longer grounding rod, or more of them, spaced 10 feet apart. The ground rods themselves should be placed in [an] area[s] that are naturally permanently moist to have any effect. Then you have to run a grounding cable that is attached to the ground rod along the bottom or top of the fence (can be the top wire or bottom wire) all the way to the fence charger. This cable needs to be attached to the ground rod by ground rod clamps That grounding cable should be attached to that fence charger in order for the fence to be properly grounded. Check out the following links on tips and instructions on how to properly ground an electric fence.
What is the minimum depth in feet that a grounding rod must be driven into the ground?
Ground rods in the U.S. on a residential home are 8 foot long and are driven 8 feet into the ground. The top of both ground rods should be flush or just under the surface. One ground rod is placed directly under the meter base and another one is placed 6 feet to either side. They are connected together and grounded to the meter base with the correct size ground wire based on the amperage of the serviced being installed.
A wire is placed on the top of a transmission line to?
Ground wireAnswerIt's a (lightning) protection wire, designed to protect the line conductors from lightning strikes.
Where is the ground wire for the ignition coil on a 93 C1500 w 5.7?
if you remove the coil cover on top of the distrubutor, there will be a red wire, a white/ or yellow wire, and a black wire which will be the ground. The Coil is not mounted on distributor in 93. It has a remote coil
Homonyms hide something in the ground?
The puppy likes to bury the bone. Mom put a single, red berry on top of each cupcake.
Where is the ground wire on the gas tank for a Chevy silverado?
Top of the frame rail.Forward of the left rear wheel.
A wire extends from the top of a building to the ground 90 feet away from the building. The wire creates an angle of elevation of 22 and ordm with the ground. How long is the wire Round to the nearest?
Length of line: 90/cos(22) = 97 feet rounded to nearest the foot
A guy wire attached to the top of a cell phone tower makes a 42° angle with the ground. What is the approximate length of the wire Round to the nearest foot?
90 ft
How do you fix the gas gauge on a 1997 Blazer?
This can get to be a real hair puller, but maybe not. Disconnect the wire going to your tank, usually on the top and hard to get to. Turn your key on then ground the wire while someone watches the guage, which should go all the way to full. If it does "and be sure you have a good ground" the sending unit in your tank is bad. If it still doesn't move, your problem is in the dash gauge or wiring.
Where is the ground wire on a 1964 Ford Falcon?
On my 64 falcon ute the ground wire goes from the battery straight to a head bolt on the front left of the engine . The head bolt has a secondary bolt threaded into the top of it . The rest of the car gets its ground from another wire that connects to the starter motor mount and goes straight to the fire wall this is only about 200mm long . Hope that helps
How do you connect the 3 pin plug?
One pin for phase other pin for neutral and third one is for earth/ground wire. In India the right pin is for phase, left pin is for neutral and pin on top side is for ground wire. This third top side pin is slightly bigger and longer compared to phase and neutral pins.
Could your starter be burnt up by the large ground wire touching one of the smaller wires on the top of the solenoid after being tightened down?
A ground wire touching smaller wires can burn out your starter. It is more likely that it will burn out the solenoid before burning out the starter.
What are the release dates for Top Shot - 2010 Bury the Hatchet 2-6?
Top Shot - 2010 Bury the Hatchet 2-6 was released on: USA: 15 March 2011
A suspension bridge is supported from a height of 30 feet. The length of the wire used to suspend the bridge from the ground to the top is 65 feet. What is the angle of elevation from the base of the?
A suspension bridge is supported from a height of 30 feet. The length of the wire used to suspend the bridge, from the ground to the top, is 65 feet. What is the angle of elevation from the base of the bridge to the point of suspension?
