0
What else can I help you with?
Adding a 220 line to panel box for a dryer?
A dryer requires a 30 amp receptacle. This will be to receive a four blade dryer plug. The wire needed will be a three copper wire #10 cable set with a bare #14 copper ground wire. The breaker will be a two pole 30 amp breaker.
Can a 30 amp fuse replace a 40 amp fuse on a lawnmower?
You can replace a higher rating fuse with a lower rating provided it works with the device without constantly blowing. So try the 30 amp fuse in your lawnmower and if it doesn't blow and the mower works okay, you are fine. If it blows you will have to go back to 40.
What size breaker can you use on a 7500watt generator?
Depends on the wire size you are using. If the generator breaker is a 30 amp then install a 30 amp breaker.
Can I use a 30 amp fuse instead of a 40?
This is not a good idea to do. Sometimes just that little bit of extra current that the 45 amp fuse will allow to reach the 40 amp load might be enough to destroy the device.
Can 600v wire works 30 amp fuse?
What size is the wire? AWG 10, 600V is rated for 30 amps. Any AWG less than 6 would also be ok for a 30 amp circuit....
Can you use a 20 amp circuit breaker for an electric dryer?
If you are referring to a cloths dryer, the answer depends on the requirements of the dryer. Most dryers require AWG#10 wire with a 30 amp fuse. If the wiring is AWG#12 then use a 20 amp breaker but never use it on AWG#10 which requires a 30 amp breaker. If you are referring to a hair dryer then yes a 20 amp breaker is fine.
What is the recommended amperage for a breaker to use with a 30 amp dryer?
The recommended amperage for a breaker to use with a 30 amp dryer is 30 amps.
What type of electrical outlet is required for a dryer that uses a 30 amp dryer plug?
A 30 amp dryer plug requires a special type of electrical outlet called a NEMA 14-30 outlet.
What is the appropriate double pole 30 amp breaker to use for a dryer installation?
The appropriate double pole 30 amp breaker to use for a dryer installation is a 30 amp double pole circuit breaker.
What is the recommended wire size for a 30 amp dryer circuit?
The recommended wire size for a 30 amp dryer circuit is typically 10 gauge wire.
Can you plug your motorhome 30 amp adapter into the dryer 30 amp outlet without hazard?
yes
How do you install and wire a dryer outlet if there is no room for a new 30 amp breaker?
If there is no room for a new 30 amp breaker, you may need to upgrade your electrical panel to accommodate the additional load. It is recommended to hire a licensed electrician to properly install the new circuit and outlet for the dryer to ensure safety and compliance with local codes.
What is the proper electrical requirement for a 30 amp dryer receptacle?
The proper electrical requirement for a 30 amp dryer receptacle is a dedicated 240 volt circuit with a 30 amp circuit breaker and a 3-prong or 4-prong outlet.
What is the maximum amperage capacity of a 30 amp fuse box?
The maximum amperage capacity of a 30 amp fuse box is 30 amps.
Can you put a 30 amp fuse in a 10 amp slot?
Not a good thing to do! If you are blowing 10 amp fuses, you have a problem with that circuit. Putting a 30 amp fuse in its place can do more damage.
What amp fuse is required for the heater fan in a 1978 Chevrolet Impala?
A 30 amp fuse is required.
How thick is a 30 amp fuse wire?
A 30 amp fuse wire typically has a diameter of around 0.08 inches (2 millimeters).
