answersLogoWhite

0

The wording of your question is a bit difficult to understand. I'm not sure what you mean by a "switch recepticle outlet."

If you mean a switch/receptacle combination device, and you want the switch to operate the receptacle, first you must remove the brass bar that connects the two brass screw terminals. This can be easily done with any set of pliers small enough to get hold of the bar. By moving it back and forth a few times it will simply come off.

Next connect your green or bare wire to the ground screw of the device. Then connect your neutral coming into the box to the nickle (or silver) screw terminal next to the receptacle. Then connect a black wire (or any color wire other than white, gray, green, or orange) from the switch leg terminal of the switch (most likely a black screw) to the brass terminal of the receptacle. Make this wire long enough to work with. There is no reason to make it so short you can't work with it if trouble shooting is ever necessary.

And finally connect your hot wire coming into the box to the brass terminal on the switch.

If all this makes absolutely no sense to you, find a competent electrician to do it for you. We do these kinds of things in our sleep. (Just kidding, of course.)

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you wire in a pull chain switch in a bathroom light fixture?

If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.


How do you disconnect a light switch and outlet that are tied together?

If there is a black wire going from the outlet to the switch and the other side of the switch goes back to the outlet then just cut these wires and connect supply wire directly to outlet. If the supply goes to the switch first, disconnect from switch and connect the two wires with a wire-nut. Some situations only switch one of the two outlets in a duplex device. Do the same thing, but also replace the outlet since the strapping between both outlets has been removed.


How do you wire a circuit so that the switch only controls the second receptacle and the first receptacle is always energized?

You will need a receptacle that you can wire each outlet separately (not jumpered). You would then wire the switch in series on the line conductor with the outlet you want switchable. Wire the other outlet directly to the power source. You can jumper the neutral from one outlet to the other.


You have two wall lights on one wall connected to one switch you want to change one light to an outlet and keep the other light on the switch How can you do this?

This depends on the specific way your installation is wired. Most likely, though, you will not be able to just change one light fixture to an outlet. Lights that are controlled together are wired with a common hot wire called a switch leg. This switch leg is connected to the switch so that when the switch is on, the wire is hot. This lights your fixtures. To change a light fixture into an outlet, you need a constantly hot wire. This wire is connected to the light switch screw opposite the switch leg. In your situation, you probably need to run new wires to the new outlet which carry this constant hot and a neutral. Or you would have to bypass the switch (wire nut the hot and switch leg together) and install outlets at both light fixture locations. Simply stated, this is not really an easy fix but more of something for an electrician to do. ----If you do not understand the work well enough to accomplish it yourself properly and safely, don't try it. Consult a professional electrician, as they are proficient enough to do it properly and safely. When working on electrical circuits and equipment, make sure to de-energize the circuit you will be working on. Then test the circuit with a definitive means to make sure it is off (multimeter with metal tipped leads, voltage tester with metal tipped leads, etc., NOT a non-contact tester, which is not definitive.)


What type of prewire for a ceiling fan light?

The pre wire for a ceiling fan light should be made with a three wire cable. This cable will have a red, black, and white wire as main conductors. This cable will also have a bare ground wire. This wire should be strung between a two gang switch box to the fixture junction box. This pre wire allows the supply to be either fed to the two gang box. From the two gang switch junction box, one side will be used for the light in the fixture and the other side of the switch junction box, itwill be used for the fan portionin the fixture.

Related Questions

How do you wire a light switch to an outlet?

To wire a light switch to an outlet, you need to connect the hot wire from the outlet to the hot terminal on the switch, and then connect the hot wire from the light fixture to the other terminal on the switch. Make sure to turn off the power before starting and follow all safety precautions.


How do you wire an outlet to a switch?

To wire an outlet to a switch, you need to connect the hot wire from the outlet to one terminal on the switch, and then connect another wire from the other terminal on the switch to the outlet. This allows the switch to control the flow of electricity to the outlet. Make sure to turn off the power before attempting any electrical work.


How do you wire a switch to an outlet?

To wire a switch to an outlet, you need to connect the hot wire from the outlet to one terminal of the switch, and then connect another wire from the other terminal of the switch to the outlet's hot terminal. This allows you to control the flow of electricity to the outlet using the switch. Make sure to turn off the power before working on the wiring to avoid any accidents.


How do you wire a switch to a light fixture?

To wire a switch to a light fixture, you will need to connect the hot wire from the power source to one terminal on the switch, then connect another wire from the other terminal on the switch to the hot terminal on the light fixture. Finally, connect the neutral wires from the power source and the light fixture together. Make sure to turn off the power before starting and follow all safety precautions.


How many line conductors are installed between the switch and light fixture?

One. A typical "two way" ON-OFF light switch is a Single Pole Single Throw (SPST) switch with two terminals. It is wired in series with the fixture: that is, the power circuit is routed from the breaker to one side of the switch. The other side of the switch is connected to the "phase" or "power" terminal of the fixture. In a 115VAC single phase circuit, the other terminal of the fixture is connected to neutral. A "three way" switch circuit consists of two switches in different locations, each of which is a Single Pole Double Throw (SPDT) switch with three terminals. A typical use would have one switch at the top and the other at the bottom of a set of stairs. For the sake of clarity, we can label the "common" terminal on a SPDT switch the "C" terminal. This terminal is internally connected to one of the other two terminals, call them "A" and "B", depending of the position of the switch. A three way switch is connected with the circuit breaker connected to the "C" terminal on either switch. Conductors connect the "A" terminal on one switch the the "A" terminal on the other switch and the "B" terminal on one switch the the "B" terminal on the other switch. The remaining "C" terminal is connected to the "phase" or "power" terminal of the fixture. The other terminal of the fixture is connected to neutral. Note that, in either case, there is no neutral wire connected to the switch. Ground conductors do connect to the chassis of the switch box and the fixture, but they do not carry current and do not affect the operation of the circuit.


How does a 3-way switch work to control the lighting in a room?

A 3-way switch is a type of electrical switch that allows you to control a light fixture from two different locations. It works by using two switches that are connected to the same light fixture. When one switch is turned on, it sends power to the light fixture, and when the other switch is turned on, it sends power to the light fixture as well. This allows you to turn the light on or off from either switch, providing convenience and flexibility in controlling the lighting in a room.


How do you properly wire a switch to a light fixture?

To properly wire a switch to a light fixture, you need to connect the hot wire from the power source to one terminal on the switch, then connect another wire from the other terminal of the switch to the hot terminal on the light fixture. Finally, connect the neutral wires from the power source and the light fixture together. Make sure to turn off the power before starting and follow all safety precautions.


How can I properly install and wire a switched outlet in my home?

To properly install and wire a switched outlet in your home, follow these steps: Turn off the power to the outlet at the circuit breaker. Remove the existing outlet from the wall. Install a new electrical box for the switch next to the outlet. Run a new wire from the outlet to the switch box. Connect the black wire from the outlet to one terminal on the switch. Connect the white wire from the outlet to the neutral wire in the switch box. Connect the black wire from the power source to the other terminal on the switch. Connect the ground wires together and to the switch and outlet. Install the switch and outlet back into the wall. Turn the power back on and test the switched outlet to ensure it is working properly.


How do you wire in a pull chain switch in a bathroom light fixture?

If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.


How did they use to wire two on off switches to one fixture?

You need two 3-way switches. To see a diagram use your favorite search engine and search for 3-way switch wiring. Each switch has a common connection point and two other terminals. Basically connect the "other" terminal on 1 switch to either "other" terminal on the second switch and then do it again for the remaining "other" terminal. Then connect the common on one switch to the fixture and the common on the remaining switch to supply voltage. Tie neutral and ground for fixture and supply to the white and bare wires respectively.


How do you wire a switch to a light?

To wire a switch to a light, you connect the hot wire from the power source to one terminal on the switch, then connect another wire from the other terminal of the switch to the hot terminal on the light fixture. Finally, connect the neutral wires from the power source and the light fixture together.


How do I properly wire a switch to a light fixture?

To properly wire a switch to a light fixture, you need to first turn off the power to the circuit. Then, connect the hot wire from the power source to one terminal on the switch, and connect the hot wire from the light fixture to the other terminal on the switch. Finally, connect the neutral wires from the power source and the light fixture together. Make sure to follow all safety precautions and consult a professional if you are unsure.