0
On the emitter there is base current which is basically a function of Beta and only at that particular current. Unfortunately the beta factor is a non linear function and it is strictly related to collector current
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why the base bias Q-point in transistor circuits changes with temperature?
why we use base resistor in emitter bias
Why it is named as self Bias of BJT?
The Self Bias of the BJT is also called the voltage divider bias. It is called thus because it can stabilize the collector current, the base emitter voltage and the amplification factor.
What is the advantages of emitter bias configurations over fixed bias configurations?
One of the main advantages of using the emitter bias configuration has to do with the Q-points. With changes in the current gain, those Q-points don't change. Since the collector current accounts for 99% of the emitter current, we come up with a 1% margin of error, much better than the 5% we can get with the fixed-base bias configuration and Ic and Vce do not fluctuate as well.
Why voltage gain of a common collecter amplifier is 1?
actually it is slightly less than 1, due to base-emitter forward bias voltage.
Is a UJT a voltage controlled or current controlled device?
voltageCurrent between the two bases of the UJT sets up a voltage gradient in the semiconductor. When the voltage on the emitter of the UJT rises high enough to forward bias the emitter-base junction at the voltage of the interbase gradient where the emitter is located, the UJT "turns on".
Why the base bias Q-point in transistor circuits changes with temperature?
why we use base resistor in emitter bias
What will happen if emitter base is reversed bias and collector base is forward bias?
If emitter-base is reverse biased then there will be no amplification effect on collector-emitter. If collector-base is forward biased, it will act like a diode, but without emitter-base current, that is meaningless.
Why emitter bias circuit is called self bias?
emitter bias provides a feedback to the circuit so that circuit remains in linear regionn
Why emitter bias circuit is called self bias circuit?
emitter bias provides a feedback to the circuit so that circuit remains in linear regionn
What will happen to the emitter current if the emitter base is reversed biased?
as we know that in reverse bias condition no current is produced and if it produced by the minority charge carrier then also the current produced is in very less amount so u can say that emitter current will reduced to large extend as compare to emitter current in forward bias condition
Why a transistor can be operated in active region?
a transistor can only work in active region cox in active region collector base junction is in reverse bias and emitter base junction is in forward bias.
What are the bias condition of the base emitter and base collector junction for a transistor to operate as a switch?
In order for a transistor to operate as a switch, the base-emitter current must be greater than the collector-emitter current divided by a factor of hFe. In this state, the transistor operates in saturated mode, fully turning on.
What are the bias conditions of the base emitter and base collector junction for a transistor to operate as a switch?
In order for a transistor to operate as a switch, the base-emitter current must be greater than the collector-emitter current divided by a factor of hFe. In this state, the transistor operates in saturated mode, fully turning on.
What is the deffbetween forward and reverse biased?
Asking about biasing of the emitter alone does not make sense. When you talk about bias, you talk about a junction, such as emitter-base or emitter-collector or base-collector. In a bipolar junction transistor (BJT) both the emitter-base and emitter-collector need to be forward biased, otherwise you are operating the BJT in cutoff mode. Certainly, if you intend to operate the BJT as a switch, then reverse bias for emitter-base (actually, zero bias) could well be one of the valid states, corresponding to a cutoff condition for emitter-collector. However, operation in linear mode, the other normal way to use a BJT, requires that both the emitter-base and the emitter-collector be forward biased. Of course, depending on the ratio of emitter-base to emitter-collector versus hFe, you could also be saturated, which is a non-linear mode, i.e. an on switch.
What do you mean by emitter bypass capacitor?
a capacitor that bypasses a BJT's emitter bias resistor so the emitter is at AC ground but has a DC bias voltage on it to set operating conditions. without the bypass, the bias would not stay constant.
Why it is named as self Bias of BJT?
The Self Bias of the BJT is also called the voltage divider bias. It is called thus because it can stabilize the collector current, the base emitter voltage and the amplification factor.
Why you use negative source in emitter biasing?
to get the base- emitter junction forward bias we should connect the negative of the diode with the negative of the battery and the positive of the diode with the positive of the diode so we should connect negative source in the emitter
